Cabinentaxi
Encyclopedia
Cabinentaxi, sometimes Cabintaxi in English, was a German
people mover
development project undertaken by Demag
and Messerschmitt-Bölkow-Blohm
with funding and support from the Bundesministerium für Forschung und Technologie (BMFT, the German Ministry of Research and Development). Cabinentaxi was designed to offer low-cost mass transit services where conventional systems, like a metro
, would be too expensive to deploy due to low ridership or high capital costs.
Cabinentaxi systems could be operated in a variety of fashions depending on the need. It is most widely known as the first true personal rapid transit
(PRT) system, where customers call up a small "car" on demand which then takes them directly to their destination without any stops along the way. The system could also be used in a group rapid transit (GRT) fashion, using larger cars with up to 18 passengers. In this case the vehicles would travel along a fixed route, stopping at any station that a passenger requested. Cabinentaxi could also mix the two modes on a single line, which allowed direct routing to high-density areas when traffic loads were low, saving the larger bus-like vehicles for the high-demand periods.
Cabinentaxi was in serious consideration for two deployments in the late 1970s; BMFT was in the process of funding a deployment in Hamburg
while their U.S. counterpart, the Urban Mass Transit Authority
(UMTA), selected it as a front-runner for a deployment in Detroit. Cabinentaxi's corporate partners decided to pull out of the Detroit competition to focus on the Hamburg development. When unrelated budget cuts drained the BMFT's coffers, the Hamburg project was also canceled, and the Cabintaxi Joint Venture gave up on the public transit field and withdrew the Cabintaxi technology from the market. The rights were purchased in 1985 by a small U.S. consortium, Cabintaxi Corporation, but no developments have followed. The only commercial use was a modified system, the Cabinlift, which operates as a horizontal elevator between buildings at the Schwalmstadt-Ziegenhain hospital in Germany.
Donn Fichter started work on a book that would eventually emerge in 1964 as Individualized Automatic Transit and the City. Fitcher argued that the only way to solve the gridlock
problems in cities being caused by increased car ownership was to use mass transit systems. Fichter argued that unless the systems operated more like a taxi
service, arriving when called for and taking the passenger directly to their destination, people would not leave their cars to use it. Busses and metro systems are not personalized, they run on pre-planned routes and schedules, making stops along the way that do not serve each individual, only the group of riders as a whole.
Fichter and other planners tapped into a zeitgeist that was being fuelled by rapid urban decay
in the U.S. President Kennedy addressed congress in 1962 and stated that "To conserve and enhance values in existing urban areas is essential. But at least as important are steps to promote economic efficiency and livability in areas of future development. Our national welfare therefore requires the provision of good urban transportation, with the properly balanced use of private vehicles and modern mass transport to help shape as well as serve urban growth." Funding provided through the U.S. Department of Housing and Urban Development (HUD) led to a series of reports by a variety of aerospace firms (notably Aerospace Corporation), today known as the "HUD reports
", that explored various concepts and provided strong support for the basic concepts. A follow-on bill later in the decade provided additional funding for development of several experimental systems, and created the Urban Mass Transit Administration (UMTA).
On the "simple end" of the scale were vehicles that used a guideway to steer, and left most other operations to a centralized control centre with some form of automatic train control
. These systems had fairly slow reaction times that demanded fairly long headway
s between the trains. Most conventional metros have headways around two minutes or more, these new systems were generally on the order of 30 seconds. To make these systems efficient at high demand levels they had to have fairly large capacities, on the order of 25 to 100 passengers, which places them in the group rapid transit, or GRT, end of the people mover spectrum. These sorts of systems can be simplified if high performance is not required; GRT systems are quite common at airports today.
On the other end of the scale were the personal rapid transit
systems, or PRTs. These systems abandoned centralized control for a simpler distributed solution based on set timings, speeds, or flocking
behaviour. By placing the headway logic on the vehicles the reaction timing was dramatically improved, because they no longer had to communicate with a centralized system for traffic information or instructions. PRTs generally worked on headways of less than 10 seconds, which greatly increased the passenger density of the system as a whole. This allowed the vehicles to be much smaller and still retain the same system capacity as the larger GRTs, while offering the sort of personalized car-like operations that Individualized Automatic Transit envisioned.
(German Federal Railway) and their safety experts. This assured that when development was completed, the systems would meet German (and by extension international) public transit standards.
When the BMFT learned of the separate efforts at Demag and MBB, they urged both companies to combine their efforts under a new joint operating company, which became Cabinentaxi. BMFT provided 80% of the total funding, considerably less than their counterparts in the U.S., which completely funded by the UMTA. By this time the system had been well-defined, and was committed to true PRT point-to-point service. In order to avoid stops along the way, stations were "off-line", on separate guideways, allowing en-route cars to pass them by. The cars themselves would handle switching along a pre-defined route, which allowed them to be directed to an optimal path in a network of any complexity. Studies suggested a three-passenger car for the basic system, although in order to increase capacity they also had cars with seating for 6, 12 and 18 passengers. These larger cars would normally be planned to operate in GRT fashion in order to increase the overall capacity of the network in the early development stages, where small networks in dense areas would not be meaningful in a small vehicle PRT mode. The larger cars could also be connected front-to-back to form two-car trains, further increasing capacity for some simple applications.
One problem with all elevated transportation system structures in general, is that the guideways (highways or transit) are widely considered to be an eyesore. In order to reduce the size of the guideways, Cabinentaxi took the uncommon approach of optionally allowing its cars to run on the top or bottom of a single track. The cars could not be switched from top to bottom, however. If this option was used, the guideways were supported on pillars that attached to the track from the side, rather than directly below. Cabinentaxi's guideway is noticeably smaller and thinner than conventional elevated systems, like the Vancouver SkyTrain. The track is approximately six feet wide, slightly smaller than a row of parking spots on the side of a city street.
, Germany. The test track was expanded several times. By October 1974 it was 1136 meters long and featured two passenger stations with a closed-loop track, adding two additional vehicles for a total of five. By 1975 it had three stations and nine vehicles. The first 12-person vehicle was introduced that October. The final expansion was completed in 1976, bringing the total track to 1.9 km with six stations and twenty-four vehicles. In 1975, Raytheon Missile Systems
examined the prototype system and decided to license it for deployment in the U.S., but a final agreement was never reached.
Cabinentaxi technology logged over 400,000 vehicle-miles between 1975 and 1978 on the Hagen test track. In 1977 the system completed fleet operation endurance testing of 7500 continuous vehicle hours, extending that in 1978 to 10,000 continuous vehicle hours. These are the only PRT fleet endurance test of these magnitudes ever carried out. Headways were reduced throughout the period, vehicle separations started at under 3 seconds, reaching 1.9 seconds in later tests, about the same as cars on a highway. The basic operating speed was also increased during testing, from the original 30 km/h to 36 in the later tests, with options for even higher speeds in production versions.
Late in the program a number of safety studies were carried out. Fire was a major concern of safety officials, but due to the simplicity of the vehicles, and a fire safety risk-reduction program it was demonstrated the possibility of fire was reduced to a non-issue. Other problems, like broken motors or a widespread power failure that demanded evacuation, were the primary areas of concern, but the solutions were found to lay in ground based equipment and in specially equipped rescue cars that could operate on the guideway and access both levels. The final system plans required no external walkways.
One Cabinlift system with two stations was installed at the Schwalmstadt-Ziegenhain hospital. A larger and more complex network was planned for the central hospital in Bremen, but funding fell through.
One was an expansion of the original Hagen system, done as much as an example of the planning process as a serious proposal. This deployment envisioned a staged development starting with the 12-passenger cars in a network of about 40 stations covering the downtown core. Additional lines would then be added until it was fully expanded with 138 km of track and 182 stations covering the majority of the city and several surrounding suburbs and towns. The outlying tracks would primarily use the smaller cars. Funding for this deployment was not forthcoming.
A system was proposed for Hamburg
, initially consisting of approximately 7.5 miles of over and under guideway with 11 stations and 50 vehicles. In 1977 Hamburger Hochbahn
estimated the total costs for this initial installation was estimated by the to be $56,568,000, or $7.5 million per double lane mile (compare with a Canadian estimate from 1980 at $75 to $80 million per mile for underground subway lines). These were not the final system costs which would have only been determined after construction, and cost increases were already being experienced as the project neared the start of construction.
The Hamburg development coincided with a request by the American government for increased defence spending by the NATO allies, which resulted in a funding cut to all other departments of the German government. BMFT withdrew funding for the Hamburg project with a statement that, among other things, the failure to pursue the export market and the mandated budget cuts led to its decision.
Cabinentaxi, as Cabintaxi, was also one of the systems approved to contend for the UMTA's Downtown People Mover Program. It was recognized as the favorite system to win the Detroit People Mover
project. For the Detroit project, the system's over-and-under beam was a major advantage as the city specified a single-beam system, and the over-and-under beam would provide bi-directional operation which the city wanted but could not otherwise get with its single beam restriction. The schedules for the Detroit People Mover Program and the Hamburg application appeared to conflict, so the consortium chose to withdraw from the US competition and concentrate on Hamburg.
J. Edward Anderson
, the well-known U.S. proponent of PRT systems, also selected Cabinentaxi for a proposed deployment in Indianapolis
. After the initial $300,000 for the study ran out, no further money was forthcoming and the plans fell through.
The developing firms found themselves without a market opportunity in Europe or the United States, and withdrew from the public transit field. Interest in the system in the U.S. lived on, and in 1985 a consortium was arranged to take over the design rights under Cabintaxi Corporation. No installations followed, however.
Cabinentaxi offered very high capacity utilization of its lines, up to 80% full before congestion would occur. Cabinentaxi also had a number of different car sizes, seating 6, 12 and 18 passengers. The larger cars could be formed into two-unit trains, although as the headways were progressively reduced in testing, the advantage of this style of operation was eliminated. Known as "SKG-A", the larger cars were substantially similar to the smaller KK3's in construction and operation.
(LIM) for the Cabinentaxi project. Linear motors were a major area of research since the 1960s when they were first introduced in the U.K. by Eric Laithwaite
. As they have no moving parts, a LIM-powered vehicle would be more reliable than one using a conventional motor. Another advantage is that there is no contact between the motor and the track, so snow or rain will not effect its performance, which means a LIM vehicle does not require additional headspace in bad weather. Also, because the traction does not rely on friction, LIMs can climb much steeper grades. On the downside, LIMs require a "reaction rail" for the motor to push against, which increases capital costs slightly.
The vehicle itself was responsible for maintaining separation from the vehicle in front of it, and automatically switching from guideway to guideway. Since the measurement and control of separation did not require communications with external systems, reaction times were greatly reduced and headways were much shorter than systems using a central computer to control spacing.
There was a centralized control system used in Cabinentaxi, but it did not have direct control over the vehicles. This system was used to plan the most efficient route when a customer selected a destination and paid for it. The calculated route was then uploaded onto a magnetic stripe on the customer's fare card. The card was then inserted into a reader to call a car from the storage area or one passing by on the line, at which point the reader uploaded the route to the car's onboard computer. Once calculated the route was static, although the customer did have the option to stop at the very next station if they pressed a button in the car.
A third system handled operations within the stations, which were "offline" from the main guideways. Stations had multiple berths for loading and unloading, as well as longer areas for acceleration and deceleration to collect vehicles as they switched on or off the main guideways. When a vehicle entered the station's off-ramp, it automatically slowed to a stop where the passengers would exit the car. The station computer would then direct it to a position in a storage ring to wait for the next customer.
When it was called for the station would switch it back onto the main platform where the passengers would use their fare card to enter the vehicle. When a vehicle was loaded, the station computer watched the traffic on the adjacent mainline and looked for gaps in the vehicles passing by the station. When a suitable gap was seen, the station would calculate the time needed for the car to accelerate up to mainline speed, and then give it the go command at the right time so it would reach the switch onto the mainline right as the gap was reaching it.
Germany
Germany , officially the Federal Republic of Germany , is a federal parliamentary republic in Europe. The country consists of 16 states while the capital and largest city is Berlin. Germany covers an area of 357,021 km2 and has a largely temperate seasonal climate...
people mover
People mover
A people mover or automated people mover is a fully automated, grade-separated mass transit system.The term is generally used only to describe systems serving relatively small areas such as airports, downtown districts or theme parks, but is sometimes applied to considerably more complex automated...
development project undertaken by Demag
Demag
Demag or Demag Cranes AG is a German heavy equipment manufacturer now controlled by US based Terex. The roots of Demag date back prior to its formation, but became Märkische Maschinenbau-Anstalt, Ludwig A.-G in 1906 as the biggest crane building company in Germany employing 250-300 people...
and Messerschmitt-Bölkow-Blohm
Messerschmitt-Bölkow-Blohm
Messerschmitt-Bölkow-Blohm was a German aerospace company formed as the result of several mergers in the late 1960s. Among its best-known products was the MBB Bo 105 light twin helicopter...
with funding and support from the Bundesministerium für Forschung und Technologie (BMFT, the German Ministry of Research and Development). Cabinentaxi was designed to offer low-cost mass transit services where conventional systems, like a metro
Rapid transit
A rapid transit, underground, subway, elevated railway, metro or metropolitan railway system is an electric passenger railway in an urban area with a high capacity and frequency, and grade separation from other traffic. Rapid transit systems are typically located either in underground tunnels or on...
, would be too expensive to deploy due to low ridership or high capital costs.
Cabinentaxi systems could be operated in a variety of fashions depending on the need. It is most widely known as the first true personal rapid transit
Personal rapid transit
Personal rapid transit , also called podcar, is a public transportation mode featuring small automated vehicles operating on a network of specially built guide ways...
(PRT) system, where customers call up a small "car" on demand which then takes them directly to their destination without any stops along the way. The system could also be used in a group rapid transit (GRT) fashion, using larger cars with up to 18 passengers. In this case the vehicles would travel along a fixed route, stopping at any station that a passenger requested. Cabinentaxi could also mix the two modes on a single line, which allowed direct routing to high-density areas when traffic loads were low, saving the larger bus-like vehicles for the high-demand periods.
Cabinentaxi was in serious consideration for two deployments in the late 1970s; BMFT was in the process of funding a deployment in Hamburg
Hamburg
-History:The first historic name for the city was, according to Claudius Ptolemy's reports, Treva.But the city takes its modern name, Hamburg, from the first permanent building on the site, a castle whose construction was ordered by the Emperor Charlemagne in AD 808...
while their U.S. counterpart, the Urban Mass Transit Authority
Federal Transit Administration
The Federal Transit Administration is an agency within the United States Department of Transportation that provides financial and technical assistance to local public transit systems. The FTA is one of ten modal administrations within the DOT...
(UMTA), selected it as a front-runner for a deployment in Detroit. Cabinentaxi's corporate partners decided to pull out of the Detroit competition to focus on the Hamburg development. When unrelated budget cuts drained the BMFT's coffers, the Hamburg project was also canceled, and the Cabintaxi Joint Venture gave up on the public transit field and withdrew the Cabintaxi technology from the market. The rights were purchased in 1985 by a small U.S. consortium, Cabintaxi Corporation, but no developments have followed. The only commercial use was a modified system, the Cabinlift, which operates as a horizontal elevator between buildings at the Schwalmstadt-Ziegenhain hospital in Germany.
Background
In the early 1950s, urban plannerUrban planner
An urban planner or city planner is a professional who works in the field of urban planning/land use planning for the purpose of optimizing the effectiveness of a community's land use and infrastructure. They formulate plans for the development and management of urban and suburban areas, typically...
Donn Fichter started work on a book that would eventually emerge in 1964 as Individualized Automatic Transit and the City. Fitcher argued that the only way to solve the gridlock
Gridlock
The term gridlock is defined as "A state of severe road congestion arising when continuous queues of vehicles block an entire network of intersecting streets, bringing traffic in all directions to a complete standstill; a traffic jam of this kind." The term originates from a situation possible in...
problems in cities being caused by increased car ownership was to use mass transit systems. Fichter argued that unless the systems operated more like a taxi
Taxicab
A taxicab, also taxi or cab, is a type of vehicle for hire with a driver, used by a single passenger or small group of passengers, often for a non-shared ride. A taxicab conveys passengers between locations of their choice...
service, arriving when called for and taking the passenger directly to their destination, people would not leave their cars to use it. Busses and metro systems are not personalized, they run on pre-planned routes and schedules, making stops along the way that do not serve each individual, only the group of riders as a whole.
Fichter and other planners tapped into a zeitgeist that was being fuelled by rapid urban decay
Urban decay
Urban decay is the process whereby a previously functioning city, or part of a city, falls into disrepair and decrepitude...
in the U.S. President Kennedy addressed congress in 1962 and stated that "To conserve and enhance values in existing urban areas is essential. But at least as important are steps to promote economic efficiency and livability in areas of future development. Our national welfare therefore requires the provision of good urban transportation, with the properly balanced use of private vehicles and modern mass transport to help shape as well as serve urban growth." Funding provided through the U.S. Department of Housing and Urban Development (HUD) led to a series of reports by a variety of aerospace firms (notably Aerospace Corporation), today known as the "HUD reports
HUD reports
The HUD Reports were a series of studies in mass transit systems, funded by the Urban Mass Transportation Administration department of the United States Department of Housing and Urban Development...
", that explored various concepts and provided strong support for the basic concepts. A follow-on bill later in the decade provided additional funding for development of several experimental systems, and created the Urban Mass Transit Administration (UMTA).
Spectrum of designs
Other companies and government organizations soon joined these efforts, as it appeared PRT systems would soon be being deployed around the world. By the early 1970s there were at least a dozen development efforts in the U.S., a similar number in Europe and Japan, and two in Canada. The systems differed considerably in operating concept.On the "simple end" of the scale were vehicles that used a guideway to steer, and left most other operations to a centralized control centre with some form of automatic train control
Automatic Train Control
Automatic Train Control is a train protection system for railways, ensuring the safe and smooth operation of trains on ATC-enabled lines. Its main advantages include making possible the use of cab signalling instead of track-side signals and the use of smooth deceleration patterns in lieu of the...
. These systems had fairly slow reaction times that demanded fairly long headway
Headway
Headway is a measurement of the distance/time between vehicles in a transit system. The precise definition varies depending on the application, but it is most commonly measured as the distance from the tip of one vehicle to the tip of the next one behind it, expressed as the time it will take for...
s between the trains. Most conventional metros have headways around two minutes or more, these new systems were generally on the order of 30 seconds. To make these systems efficient at high demand levels they had to have fairly large capacities, on the order of 25 to 100 passengers, which places them in the group rapid transit, or GRT, end of the people mover spectrum. These sorts of systems can be simplified if high performance is not required; GRT systems are quite common at airports today.
On the other end of the scale were the personal rapid transit
Personal rapid transit
Personal rapid transit , also called podcar, is a public transportation mode featuring small automated vehicles operating on a network of specially built guide ways...
systems, or PRTs. These systems abandoned centralized control for a simpler distributed solution based on set timings, speeds, or flocking
Flocking (behavior)
Flocking behavior is the behavior exhibited when a group of birds, called a flock, are foraging or in flight. There are parallels with the shoaling behavior of fish, the swarming behavior of insects, and herd behavior of land animals....
behaviour. By placing the headway logic on the vehicles the reaction timing was dramatically improved, because they no longer had to communicate with a centralized system for traffic information or instructions. PRTs generally worked on headways of less than 10 seconds, which greatly increased the passenger density of the system as a whole. This allowed the vehicles to be much smaller and still retain the same system capacity as the larger GRTs, while offering the sort of personalized car-like operations that Individualized Automatic Transit envisioned.
Cabinentaxi
In 1969 Demag and MBB independently started projects studying PRT systems as a result of the HUD reports. At the time, the Bundesministerium für Forschung und Technologie (BMFT) was involved in a wide variety of transport research, including a variety of maglev trains for high-speed service, several automated railway systems, as well as more mundane research in railway safety and signalling. Significant within the transportation development programs of the BMFT was the direct involvement of the VOV (German Association of Public Transit Operators), the Deutsche BundesbahnDeutsche Bundesbahn
The Deutsche Bundesbahn or DB was formed as the state railway of the newly established Federal Republic of Germany on September 7, 1949 as a successor of the Deutsche Reichsbahn-Gesellschaft '...
(German Federal Railway) and their safety experts. This assured that when development was completed, the systems would meet German (and by extension international) public transit standards.
When the BMFT learned of the separate efforts at Demag and MBB, they urged both companies to combine their efforts under a new joint operating company, which became Cabinentaxi. BMFT provided 80% of the total funding, considerably less than their counterparts in the U.S., which completely funded by the UMTA. By this time the system had been well-defined, and was committed to true PRT point-to-point service. In order to avoid stops along the way, stations were "off-line", on separate guideways, allowing en-route cars to pass them by. The cars themselves would handle switching along a pre-defined route, which allowed them to be directed to an optimal path in a network of any complexity. Studies suggested a three-passenger car for the basic system, although in order to increase capacity they also had cars with seating for 6, 12 and 18 passengers. These larger cars would normally be planned to operate in GRT fashion in order to increase the overall capacity of the network in the early development stages, where small networks in dense areas would not be meaningful in a small vehicle PRT mode. The larger cars could also be connected front-to-back to form two-car trains, further increasing capacity for some simple applications.
One problem with all elevated transportation system structures in general, is that the guideways (highways or transit) are widely considered to be an eyesore. In order to reduce the size of the guideways, Cabinentaxi took the uncommon approach of optionally allowing its cars to run on the top or bottom of a single track. The cars could not be switched from top to bottom, however. If this option was used, the guideways were supported on pillars that attached to the track from the side, rather than directly below. Cabinentaxi's guideway is noticeably smaller and thinner than conventional elevated systems, like the Vancouver SkyTrain. The track is approximately six feet wide, slightly smaller than a row of parking spots on the side of a city street.
Prototypes and testing
Testing of the motor and control systems started in 1972 on a 13 meter closed-loop track, running for 18 months. This was followed in August 1973 by a 150 meter test track and three 3-passenger vehicles installed near HagenHagen
Hagen is the 39th-largest city in Germany, located in the federal state of North Rhine-Westphalia. It is located on the eastern edge of the Ruhr area, 15 km south of Dortmund, where the rivers Lenne, Volme and Ennepe meet the river Ruhr...
, Germany. The test track was expanded several times. By October 1974 it was 1136 meters long and featured two passenger stations with a closed-loop track, adding two additional vehicles for a total of five. By 1975 it had three stations and nine vehicles. The first 12-person vehicle was introduced that October. The final expansion was completed in 1976, bringing the total track to 1.9 km with six stations and twenty-four vehicles. In 1975, Raytheon Missile Systems
Raytheon Missile Systems
Raytheon Missile Systems Company is a subsidiary of Raytheon Company. Headquartered in Tucson, Arizona, its president is Taylor W. Lawrence. Formerly, known as Hughes Missile Systems Company before being acquired by Raytheon Company....
examined the prototype system and decided to license it for deployment in the U.S., but a final agreement was never reached.
Cabinentaxi technology logged over 400,000 vehicle-miles between 1975 and 1978 on the Hagen test track. In 1977 the system completed fleet operation endurance testing of 7500 continuous vehicle hours, extending that in 1978 to 10,000 continuous vehicle hours. These are the only PRT fleet endurance test of these magnitudes ever carried out. Headways were reduced throughout the period, vehicle separations started at under 3 seconds, reaching 1.9 seconds in later tests, about the same as cars on a highway. The basic operating speed was also increased during testing, from the original 30 km/h to 36 in the later tests, with options for even higher speeds in production versions.
Late in the program a number of safety studies were carried out. Fire was a major concern of safety officials, but due to the simplicity of the vehicles, and a fire safety risk-reduction program it was demonstrated the possibility of fire was reduced to a non-issue. Other problems, like broken motors or a widespread power failure that demanded evacuation, were the primary areas of concern, but the solutions were found to lay in ground based equipment and in specially equipped rescue cars that could operate on the guideway and access both levels. The final system plans required no external walkways.
Cabinlift
While work on the basic Cabinentaxi continued, a modified version known as Cabinlift was also developed. Originally designed for installations in healthcare facilities, Cabinlift was based on substantially similar technology as the basic Cabinentaxi. The Cabinlift cars were larger and taller, allowing easy walk-on access for passengers and bulky loads, notably wheeled hospital beds and gurneys. The cars could be built with the doors on the side, or on the ends. Unlike Cabinentaxi, passengers in Cabinlift could stand with some fold-down seats available.One Cabinlift system with two stations was installed at the Schwalmstadt-Ziegenhain hospital. A larger and more complex network was planned for the central hospital in Bremen, but funding fell through.
Deployment projects
When the safety studies were completed the various levels of government signed off on the system and released it for commercial development. Several developments were already being studied by that point.One was an expansion of the original Hagen system, done as much as an example of the planning process as a serious proposal. This deployment envisioned a staged development starting with the 12-passenger cars in a network of about 40 stations covering the downtown core. Additional lines would then be added until it was fully expanded with 138 km of track and 182 stations covering the majority of the city and several surrounding suburbs and towns. The outlying tracks would primarily use the smaller cars. Funding for this deployment was not forthcoming.
A system was proposed for Hamburg
Hamburg
-History:The first historic name for the city was, according to Claudius Ptolemy's reports, Treva.But the city takes its modern name, Hamburg, from the first permanent building on the site, a castle whose construction was ordered by the Emperor Charlemagne in AD 808...
, initially consisting of approximately 7.5 miles of over and under guideway with 11 stations and 50 vehicles. In 1977 Hamburger Hochbahn
Hamburger Hochbahn
Hamburger Hochbahn AG or HHA is a company operating the underground system and large parts of the bus system in Hamburg, Germany, founded in 1911 it is headquartered in Hamburg.-History:...
estimated the total costs for this initial installation was estimated by the to be $56,568,000, or $7.5 million per double lane mile (compare with a Canadian estimate from 1980 at $75 to $80 million per mile for underground subway lines). These were not the final system costs which would have only been determined after construction, and cost increases were already being experienced as the project neared the start of construction.
The Hamburg development coincided with a request by the American government for increased defence spending by the NATO allies, which resulted in a funding cut to all other departments of the German government. BMFT withdrew funding for the Hamburg project with a statement that, among other things, the failure to pursue the export market and the mandated budget cuts led to its decision.
Cabinentaxi, as Cabintaxi, was also one of the systems approved to contend for the UMTA's Downtown People Mover Program. It was recognized as the favorite system to win the Detroit People Mover
Detroit People Mover
The Detroit People Mover is a automated people mover system which operates on a single set of tracks, and encircles downtown Detroit, Michigan....
project. For the Detroit project, the system's over-and-under beam was a major advantage as the city specified a single-beam system, and the over-and-under beam would provide bi-directional operation which the city wanted but could not otherwise get with its single beam restriction. The schedules for the Detroit People Mover Program and the Hamburg application appeared to conflict, so the consortium chose to withdraw from the US competition and concentrate on Hamburg.
J. Edward Anderson
J. Edward Anderson
John Edward Anderson is an American engineer and proponent of personal rapid transit.-Career:Anderson was born in China in the 1920s. His family returned to the United States in the 1930s. He obtained a BS from Iowa State University and a masters from the University of Minnesota - both in the...
, the well-known U.S. proponent of PRT systems, also selected Cabinentaxi for a proposed deployment in Indianapolis
Indianapolis
Indianapolis is the capital of the U.S. state of Indiana, and the county seat of Marion County, Indiana. As of the 2010 United States Census, the city's population is 839,489. It is by far Indiana's largest city and, as of the 2010 U.S...
. After the initial $300,000 for the study ran out, no further money was forthcoming and the plans fell through.
The developing firms found themselves without a market opportunity in Europe or the United States, and withdrew from the public transit field. Interest in the system in the U.S. lived on, and in 1985 a consortium was arranged to take over the design rights under Cabintaxi Corporation. No installations followed, however.
Vehicles
The primary vehicle design for the Cabinentaxi system was the "KK 3", a three-passenger vehicle with a semi-automatic doors. There was enough room between the seats for bulky loads like prams or bicycles. The doors were semi-automatic, locking and unlocking under vehicle control, but slid open or closed by the passengers. The vehicle bodies were made of aluminum over a steel chassis, riding on solid rubber wheels that engaged the guidance rails in the track.Cabinentaxi offered very high capacity utilization of its lines, up to 80% full before congestion would occur. Cabinentaxi also had a number of different car sizes, seating 6, 12 and 18 passengers. The larger cars could be formed into two-unit trains, although as the headways were progressively reduced in testing, the advantage of this style of operation was eliminated. Known as "SKG-A", the larger cars were substantially similar to the smaller KK3's in construction and operation.
Motor and power supply
In order to provide fine control over vehicle spacing and reduce maintenance costs, the companies selected a linear motorLinear motor
A linear motor is an electric motor that has had its stator and rotor "unrolled" so that instead of producing a torque it produces a linear force along its length...
(LIM) for the Cabinentaxi project. Linear motors were a major area of research since the 1960s when they were first introduced in the U.K. by Eric Laithwaite
Eric Laithwaite
Eric Roberts Laithwaite was a British electrical engineer, known as the "Father of Maglev" for his development of the linear induction motor and maglev rail system.- Biography :...
. As they have no moving parts, a LIM-powered vehicle would be more reliable than one using a conventional motor. Another advantage is that there is no contact between the motor and the track, so snow or rain will not effect its performance, which means a LIM vehicle does not require additional headspace in bad weather. Also, because the traction does not rely on friction, LIMs can climb much steeper grades. On the downside, LIMs require a "reaction rail" for the motor to push against, which increases capital costs slightly.
Guideway
Cabinentaxi was designed to allow top or bottom running of the vehicles, or both on one track.Guidance and control
Cabinentaxi's control system was decentralized, with three different control systems, each in command of one portion of the system's overall operation.The vehicle itself was responsible for maintaining separation from the vehicle in front of it, and automatically switching from guideway to guideway. Since the measurement and control of separation did not require communications with external systems, reaction times were greatly reduced and headways were much shorter than systems using a central computer to control spacing.
There was a centralized control system used in Cabinentaxi, but it did not have direct control over the vehicles. This system was used to plan the most efficient route when a customer selected a destination and paid for it. The calculated route was then uploaded onto a magnetic stripe on the customer's fare card. The card was then inserted into a reader to call a car from the storage area or one passing by on the line, at which point the reader uploaded the route to the car's onboard computer. Once calculated the route was static, although the customer did have the option to stop at the very next station if they pressed a button in the car.
A third system handled operations within the stations, which were "offline" from the main guideways. Stations had multiple berths for loading and unloading, as well as longer areas for acceleration and deceleration to collect vehicles as they switched on or off the main guideways. When a vehicle entered the station's off-ramp, it automatically slowed to a stop where the passengers would exit the car. The station computer would then direct it to a position in a storage ring to wait for the next customer.
When it was called for the station would switch it back onto the main platform where the passengers would use their fare card to enter the vehicle. When a vehicle was loaded, the station computer watched the traffic on the adjacent mainline and looked for gaps in the vehicles passing by the station. When a suitable gap was seen, the station would calculate the time needed for the car to accelerate up to mainline speed, and then give it the go command at the right time so it would reach the switch onto the mainline right as the gap was reaching it.
Loading and system capacity
Key to the efficient operation of any PRT system is the queuing of free vehicles throughout the stations on the system. Increasing the number of idle vehicles reduces the passenger wait times, as well as reducing the need to move empty vehicles through the system in order to pick up passengers. However, this also requires additional vehicles, thereby increasing capital costs. Communications between the centralized computer and the station computers allowed cars to be switched from station to station in order to keep the stations supplied with free vehicles.Further reading
External links
- CabinenTaxi promotional video, showing the test system in use in Hagen, along with simulated views of a downtown deployment. In English.