In the context of mobile and cellular communication systems, RF Planning is the process of assigning frequencies, transmitter locations and parameters of a wireless communications system to provide sufficient coverage and capacity for the services required (e.g. mobile telephony). The RF plan of a cellular communication system revolves around two principal objectives; Coverage and Capacity Coverage relates to the geographical footprint within the system that has sufficient RF signal strength to provide for a call/data session. Capacity relates to the capability of the system to sustain a given number of subscribers. In the majority of cellular communication systems, both capacity and coverage are interrelated. To improve quality some coverage, capacity has to be sacrificed, while to improve capacity, coverage will have to be sacrificed (See An Introduction to LTE RF Planning for a detailed description).

The RF Planning process consists of four major stages:

Phase 1: Initial Radio Link Budgeting

The first level of the RF planning process is a budgetary level. It uses the RF Link Budget

Link budget

A link budget is the accounting of all of the gains and losses from the transmitter, through the medium to the receiver in a telecommunication system. It accounts for the attenuation of...

 along with a statistical propagation model (e.g. Hata, COST-231 Hata or Erceg-Greenstein) to approximate the coverage area of the planned sites and to eventually determine how many sites are required for the particular RF communication system. The statistical propagation model does not include terrain effects and has a slope and intercept value for each type of environment (Rural, Urban, Suburban, etc.). This fairly simplistic approach allows for a quick analysis of the number of sites that may be required to cover a certain area. Following is a typical list of outputs produced at this stage:

• Estimated Number of Sites

Phase 2: Detailed RF Propagation Modelling

The second level of the RF Planning process relies a more detailed propagation model. Automatic planning tools are often employed in this phase to perform detailed predictions. The propagation model takes into account the characteristics of the selected antenna, the terrain, and the land use and land clutter surrounding each site. Since these factors are considered, this propagation model provides a better estimate of the coverage of the sites than the initial statistical propagation model. Thus, its use, in conjunction with the RF link budget, produces a more accurate determination of the number of sites required. Following is a typical list of outputs produced at this stage:

• Number of Sites and Site Locations (and Height)
• Antenna Directions and Downtilts
• Neighbour Cell Lists for each site
• Mobility (Handover and Cell Reselection) Parameters for each site.
• Frequency Plan
• Detailed Coverage Predictions (e.g. Signal Strength (RSRP), Signal Quality (RSRQ) Best CINR, Best Server Areas, Uplink and Downlink Throughput)

Phase 3: Fine Tuning and Optimisation

The third phase of the RF planning process incorporates further detail into the RF plan. This stage includes items such as collecting drive data to be used to tune or calibrate the propagation prediction model, predicting the available data throughput at each site, fine tuning of parameter settings (e.g. antenna orientation, downtilting, frequency plan). This process is required in the deployment of the system or in determining service contract based coverage. Following is a typical list of outputs produced at this stage:

• A final List of Sites and Site Locations (and Height)
• Optimised Antenna Directions and Downtilts
• An optimised Neighbour Cell Lists for each site
• Mobility (Handover and Cell Reselection) Parameters for each site.
• An optimised Frequency Plan
• Detailed Coverage Predictions (e.g. Signal Strength (RSRP), Signal Quality (RSRQ) Best CINR, Best Server Areas, Uplink and Downlink Throughput)

Phase 4: Continuous Optimisation

The final phase of the RF planning process involves continuous optimisation of the RF plan to accommodate for changes in the environment or additional service requirements (e.g. additional coverage or capacity). This phase starts from initial network deployment and involves collecting measurement data on a regular basis that could be via drive testing or centralised collection. The data is then used to plan new sites or to optimize the parameter settings (e.g. antenna orientation, downtilting, frequency plan) of existing sites.

See also

• Friis transmission equation
  Friis transmission equation
  The Friis transmission equation is used in telecommunications engineering, and gives the power received by one antenna under idealized conditions given another antenna some distance away transmitting a known amount of power. The formula was derived in 1945 by Danish-American radio engineer Harald T...
  
  
• Decibel
  Decibel
  The decibel is a logarithmic unit that indicates the ratio of a physical quantity relative to a specified or implied reference level. A ratio in decibels is ten times the logarithm to base 10 of the ratio of two power quantities...
  
  
• Isotropic radiator
  Isotropic radiator
  An isotropic radiator is a theoretical point source of electromagnetic or sound waves which radiates the same intensity of radiation in all directions. It has no preferred direction of radiation. It radiates uniformly in all directions over a sphere centred on the source...
  
  
• Radiation pattern
  Radiation pattern
  In the field of antenna design the term radiation pattern most commonly refers to the directional dependence of the strength of the radio waves from the antenna or other source ....
  
  
• Multipath propagation
• Free space loss
• Link Budget
  Link budget
  A link budget is the accounting of all of the gains and losses from the transmitter, through the medium to the receiver in a telecommunication system. It accounts for the attenuation of...