|
|
|
|
Solar collector
|
| |
|
| |
A solar collector is a device for extracting the energy of the sun directly into a more usable or storable form. The energy in sunlight is in the form of electromagnetic radiation from the infrared (long) to the ultraviolet (short) wavelengths. The solar energy striking the earth's surface at any one time depends on weather conditions, as well as location and orientation of the surface, but overall, it averages about 1000 watts per square meter under clear skies with the surface directly perpendicular to the sun's rays.
solar heating system consists of the collector described above; a heat transfer circuit that includes the fluid and the means to circulate it; and a storage system including a heat exchanger (if the fluid circulating through the collector is not the same liquid being used to heat the object of the system).
Discussion
Ask a question about 'Solar collector' Start a new discussion about 'Solar collector' Answer questions from other users |
Recent Posts
Encyclopedia
A solar collector is a device for extracting the energy of the sun directly into a more usable or storable form. The energy in sunlight is in the form of electromagnetic radiation from the infrared (long) to the ultraviolet (short) wavelengths. The solar energy striking the earth's surface at any one time depends on weather conditions, as well as location and orientation of the surface, but overall, it averages about 1000 watts per square meter under clear skies with the surface directly perpendicular to the sun's rays.
Design
The solar heating system consists of the collector described above; a heat transfer circuit that includes the fluid and the means to circulate it; and a storage system including a heat exchanger (if the fluid circulating through the collector is not the same liquid being used to heat the object of the system). The system may or may not include secondary distribution of heat among different storage reservoirs or users of the heat. The system can be used in a variety of ways, including warming domestic hot water, heating swimming pools, heating water for a radiator or floor-coil heating circuit, heating an industrial dryer, or providing input energy for a cooling system, among others.
The heat is normally stored in insulated storage tanks full of water. Heat storage is usually intended to cover a day or two's requirements, but other concepts exist including seasonal storage (where summer solar energy is used for winter heating by just raising the temperature by a few degrees of several million litres of water (numerous pilot housing projects in Germany and elsewhere use this concept).
System types
For solar heating of domestic hot water, two common system types are thermosyphon and pumped. In the thermosyphon system, a storage tank is placed above the collector. As the water in the collector is heated, it will rise and naturally start to circulate around the tank. This draws in colder water from the bottom of the tank. This system is self-regulating and requires no moving parts or external energy, so is very attractive. Its main drawback is the need for the tank to be placed at a level higher than the collector, which may prove to be physically difficult. A pumped system uses a pump to circulate the water, so the tank can be positioned independently of the collector location. This system requires external energy to run the pump (though this can be solar, since the water should only be circulated when there is incident sunlight). It also requires control electronics to measure the temperature gradient across the collector and modulate the pump accordingly. Systems using solar electric pumping and controls are known as zero carbon solar while those using mains electricity are known as low carbon, since they typically have a 10-20% carbon drawback.
Placement
Solar collectors can be mounted on a roof but need to face the sun, so a north-facing roof in the southern hemisphere, and a south-facing roof in the northern hemisphere is ideal. Collectors are usually also angled to suit the latitude of the location. Where sunshine is readily available, a 2 to 10 square metre array will provide all the hot water heating required for a typical family house. Such systems are a key feature of sustainable housing, since water and space heating is usually the largest single consumer of energy in households.
Solar thermal collectors
A solar thermal collector that stores heat energy is called a "batch" type system. Other types of solar thermal collectors do not store energy but instead use fluid circulation (usually water or an antifreeze solution) to transfer the heat for direct use or storage in an insulated reservoir. Water/glycol has a high thermal capacity and is therefore convenient to handle. The direct radiation is captured using a dark colored surface which absorbs the radiation as heat and conducts it to the transfer fluid. Metal makes a good thermal conductor, especially copper and aluminium. In high performance collectors, a "selective surface" is used in which the collector surface is coated with a material having properties of high-absorption and low-emissivity. The selective surface reduces heat-loss caused by infrared radiant emission from the collector to ambient. Another method of reducing radiant heat-loss employs a transparent window such as clear UV stabilized plastic or Low-emissivity glass plate. Again, Low-E materials are the most effective, particularly the type optimized for solar gain. Borosilicate glass or "Pyrex" (tm) has low-emissivity properties, which may be useful, particularly for solar cooking applications.
As it heats up, thermal losses from the collector itself will reduce its efficiency, resulting in increased radiation, primarily infrared. This is countered in two ways. First, a glass plate is placed above the collector plate which will trap the radiated heat within the airspace below it. This exploits the so-called greenhouse effect, which is in this case a property of the glass: it readily transmits solar radiation in the visible and ultraviolet spectrum, but does not transmit the lower frequency infrared re-radiation very well. The glass plate also traps air in the space, thus reducing heat losses by convection. The collector housing is also insulated below and laterally to reduce its heat loss. The second way efficiency is improved is by cooling the absorber plate. This is done by ensuring that the coldest available heat transfer fluid is circulated through the absorber, and with a sufficient flow rate. The fluid carries away the absorbed heat, thus cooling the absorber. The warmed fluid leaving the collector is either directly stored, or else passes through a heat exchanger to warm another tank of water, or is used to heat a building directly. The temperature differential across an efficient solar collector is usually only 10 or 20°C. While a large differential may seem impressive, it is in fact an indication of a less efficient design.
See also
External links
|
| |
|
|
