Oil pressure (internal combustion engine)
Encyclopedia
Oil pressure is an important factor in the longevity of most internal combustion engine
s. With a forced lubrication
system (invented by Frederick Lanchester
), oil is picked up by a positive displacement oil pump
and forced through oil galleries (passageways) into bearings
, such as the main bearing
s, big ends and camshaft
bearings. Other components such as cam lobes and cylinder walls are lubricated by oil jets.
Sufficient oil pressure ensures that the metal of the rotating shaft (journal) and the bearing shell can never touch, and wear is therefore confined to initial start-up and shutdown. The oil pressure, combined with the rotation of the shaft, also hydrodynamically centers the journal in its shell and cools the bearings. Such a bearing is known as a fluid bearing.
Oil pressure is higher when the engine is cold due to the increased viscosity
of the oil, and also increases with engine speed until the relief valve opens to divert excess flow. Oil pressure is lowest under hot idling conditions, and the minimum pressure allowed by the manufacturer's tolerances is usually given at this point. Excessive oil pressure may indicate a blocked filter, blocked oil gallery or the wrong grade of oil. Low oil pressure indicates worn bearings on the crank shaft or a broken oil pump.
Internal combustion engine
The internal combustion engine is an engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber. In an internal combustion engine, the expansion of the high-temperature and high -pressure gases produced by combustion apply direct force to some component of the engine...
s. With a forced lubrication
Lubrication
Lubrication is the process, or technique employed to reduce wear of one or both surfaces in close proximity, and moving relative to each another, by interposing a substance called lubricant between the surfaces to carry or to help carry the load between the opposing surfaces. The interposed...
system (invented by Frederick Lanchester
Frederick Lanchester
Frederick William Lanchester, Hon FRAeS was an English polymath and engineer who made important contributions to automotive engineering, aerodynamics and co-invented the field of operations research....
), oil is picked up by a positive displacement oil pump
Oil pump
Oil pump may refer to:*A hydraulic pump, which pressurizes hydraulic fluid in a hydraulic system*An oil pump , a part of the lubrication system that pressurizes motor oil for distribution around the engine...
and forced through oil galleries (passageways) into bearings
Bearing (mechanical)
A bearing is a device to allow constrained relative motion between two or more parts, typically rotation or linear movement. Bearings may be classified broadly according to the motions they allow and according to their principle of operation as well as by the directions of applied loads they can...
, such as the main bearing
Main bearing
In a piston engine, the main bearings are the bearings on which the crankshaft rotates, usually plain or journal bearings.All engines have a minimum of two main bearings, one at each end of the crankshaft, and they may have as many as one more than the number of crank pins...
s, big ends and camshaft
Camshaft
A camshaft is a shaft to which a cam is fastened or of which a cam forms an integral part.-History:An early cam was built into Hellenistic water-driven automata from the 3rd century BC. The camshaft was later described in Iraq by Al-Jazari in 1206. He employed it as part of his automata,...
bearings. Other components such as cam lobes and cylinder walls are lubricated by oil jets.
Sufficient oil pressure ensures that the metal of the rotating shaft (journal) and the bearing shell can never touch, and wear is therefore confined to initial start-up and shutdown. The oil pressure, combined with the rotation of the shaft, also hydrodynamically centers the journal in its shell and cools the bearings. Such a bearing is known as a fluid bearing.
Oil pressure is higher when the engine is cold due to the increased viscosity
Viscosity
Viscosity is a measure of the resistance of a fluid which is being deformed by either shear or tensile stress. In everyday terms , viscosity is "thickness" or "internal friction". Thus, water is "thin", having a lower viscosity, while honey is "thick", having a higher viscosity...
of the oil, and also increases with engine speed until the relief valve opens to divert excess flow. Oil pressure is lowest under hot idling conditions, and the minimum pressure allowed by the manufacturer's tolerances is usually given at this point. Excessive oil pressure may indicate a blocked filter, blocked oil gallery or the wrong grade of oil. Low oil pressure indicates worn bearings on the crank shaft or a broken oil pump.