|
|
|
|
Oil well
|
| |
|
| |
An oil well is a general term for any boring through the Earth's surface designed to find and produce petroleum oil hydrocarbons. Usually some natural gas is produced along with the oil, and a well designed to produce mainly or only gas may be termed a gas well.
The earliest known oil wells were drilled in China in 347 CE.
Discussion
Ask a question about 'Oil well' Start a new discussion about 'Oil well' Answer questions from other users |
Recent Posts
Encyclopedia
An oil well is a general term for any boring through the Earth's surface designed to find and produce petroleum oil hydrocarbons. Usually some natural gas is produced along with the oil, and a well designed to produce mainly or only gas may be termed a gas well.
The earliest known oil wells were drilled in China in 347 CE. They had depths of up to about and were drilled using bits attached to bamboo poles. The oil was burned to evaporate brine and produce salt. By the 10th century, extensive bamboo pipelines connected oil wells with salt springs. The ancient records of China and Japan are said to contain many allusions to the use of natural gas for lighting and heating. Petroleum was known as burning water in Japan in the 7th century.
The Middle East's petroleum industry was established by the 8th century, when the streets of the newly constructed Baghdad were paved with tar, derived from petroleum that became accessible from natural fields in the region. Petroleum was distilled by the Persian alchemist Muhammad ibn Zakariya Razi (Rhazes) in the 9th century, producing chemicals such as kerosene in the alembic (al-ambiq), and which was mainly used for kerosene lamps. Arab and Persian chemists also distilled crude oil in order to produce flammable products for military purposes. Through Islamic Spain, distillation became available in Western Europe by the 12th century.
Some sources claim that from the 9th century, oil fields were exploited in the area around modern Baku, Azerbaijan, to produce naphtha for the petroleum industry. These fields were described by Marco Polo in the 13th century, who described the output of those oil wells as hundreds of shiploads. When Marco Polo in 1264 visited the Azerbaijani city of Baku, on the shores of the Caspian Sea, he saw oil being collected from seeps. He wrote that "on the confines toward Geirgine there is a fountain from which oil springs in great abundance, inasmuch as a hundred shiploads might be taken from it at one time."
Shallow pits were dug at the Baku seeps in ancient times to facilitate collecting oil, and hand-dug holes up to 35 meters (115 ft) deep were in use by 1594. These holes were essentially oil wells. Apparently 116 of these wells in 1830 produced 3,840 metric tons (about 28000 barrels) of oil. In 1849, Russian engineer F.N. Semyenov used a cable tool to drill an oil well on the Apsheron Peninsula, ten years before Colonel Drake's famous well in Pennsylvania. Also, offshore drilling started up at Baku at Bibi-Eibat field near the end of the 19th century, about the same time that the first offshore oil well was drilled in 1896 at Summerland field on the California Coast.
The earliest oil wells were drilled percussively by hammering a cable tool into the earth. Soon after, cable tools were replaced with rotary drilling, which could drill boreholes to much greater depths and in less time. The record-depth Kola Borehole used non-rotary mud motor drilling to achieve a depth of over 12 000 meters (38,000 ft).
Until the 1970s, most oil wells were vertical (although different lithology and mechanical imperfections cause most wells to deviate at least slightly from true vertical). However, modern directional drilling technologies allow for strongly deviated wells which can, given sufficient depth and with the proper tools, actually become horizontal. This is of great value as the reservoir rocks which contain hydrocarbons are usually horizontal, or sub-horizontal; a horizontal wellbore placed in a production zone has more surface area in the production zone than a vertical well, resulting in a higher production rate. The use of deviated and horizontal drilling has also made it possible to reach reservoirs several kilometers or miles away from the drilling location (extended reach drilling), allowing for the production of hydrocarbons located below locations that are either difficult to place a drilling rig on, environmentally sensitive, or populated.
Life of a well
The creation and life of a well can be divided up into five segments:
- Planning
- Drilling
- Completion
- Production
- Abandonment
Drilling
The well is created by drilling a hole 5 to 36 inches (127.0 mm to 914.4 mm) diameter into the earth with a drilling rig which rotates a drill string with a bit attached. After the hole is drilled, sections of steel tubing (casing), slightly smaller in diameter than the borehole, are placed in the hole. Cement may be placed between the outside of the casing and the borehole. The casing provides structural integrity to the newly drilled wellbore in addition to isolating potentially dangerous high pressure zones from each other and from the surface.
With these zones safely isolated and the formation protected by the casing, the well can be drilled deeper (into potentially more-unstable and violent formations) with a smaller bit, and also cased with a smaller size casing. Modern wells often have 2-5 sets of subsequently smaller hole sizes drilled inside one another, each cemented with casing.
To drill the well
- The drill bit, aided by the weight of thick walled pipes called "drill collars" above it, cuts into the rock. There are different types of drillbit, some cause the rock to fail by compressive failure. Others shear slices off the rock as the bit turns.
- Drilling fluid (aka "mud") is pumped down the inside of the drill pipe and exits at the drill bit. Drilling mud is a complex mixture of fluids, solids and chemicals which must be carefully tailored to provide the correct physical and chemical characteristics required to safely drill the well., Particular functions of the drilling mud include cooling the bit, lifting rock cuttings to the surface, preventing destabilisation of the rock in the wellbore walls and overcoming the pressure of fluids inside the rock so that these fluids don't enter the wellbore.
- The generated rock "cuttings" are swept up by the drilling fluid as it circulates back to surface outside the drill pipe. The fluid then goes through "shakers" which strain the cuttings from the good fluid which is returned to the pit. Watching for abnormalities in the returning cuttings and monitoring pit volume or rate of returning fluid are imperative to catch "kicks" (when the formation pressure at the depth of the bit is more than the hydrostatic head of the mud above, which if not controlled temporarily by closing the blowout preventers and ultimately by increasing the density of the drilling fluid would allow formation fluids and mud to come up uncontrollably) early.
- The pipe or drill string to which the bit is attached is gradually lengthened as the well gets deeper by screwing in additional 30-foot (10 m) joints (i.e., sections) of pipe under the kelly or topdrive at the surface. This process is called making a connection. Usually joints are combined into 3 joints equaling 1 stand. Some smaller rigs only use 2 joints and some rigs can handle stands of 4 joints.
This process is all facilitated by a drilling rig which contains all necessary equipment to circulate the drilling fluid, hoist and turn the pipe, control downhole pressures, remove cuttings from the drilling fluid, and generate onsite power for these operations.
Completion
After drilling and casing the well, it must be 'completed'. Completion is the process in which the well is enabled to produce oil or gas.
In a cased-hole completion, small holes called perforations are made in the portion of the casing which passed through the production zone, to provide a path for the oil to flow from the surrounding rock into the production tubing. In open hole completion, often 'sand screens' or a 'gravel pack' is installed in the last drilled, uncased reservoir section. These maintain structural integrity of the wellbore in the absence of casing, while still allowing flow from the reservoir into the wellbore. Screens also control the migration of formation sands into production tubulars and surface equipment, which can cause washouts and other problems, particularly from unconsolidated sand formations in offshore fields.
After a flow path is made, acids and fracturing fluids are pumped into the well to fracture, clean, or otherwise prepare and stimulate the reservoir rock to optimally produce hydrocarbons into the wellbore. Finally, the area above the reservoir section of the well is packed off inside the casing, and connected to the surface via a smaller diameter pipe called tubing. This arrangement provides a redundant barrier to leaks of hydrocarbons as well as allowing damaged sections to be replaced. Also, the smaller diameter of the tubing produces hydrocarbons at an increased velocity in order to overcome the hydrostatic effects of heavy fluids such as water.
In many wells, the natural pressure of the subsurface reservoir is high enough for the oil or gas to flow to the surface. However, this is not always the case, especially in depleted fields where the pressures have been lowered by other producing wells, or in low permeability oil reservoirs. Installing a smaller diameter tubing may be enough to help the production, but artificial lift methods may also be needed. Common solutions include downhole pumps, gas lift, or surface pump jacks. Many new systems in the last ten years have been introduced for well completion. Multiple packer systems with frac ports or port collars in an all in one system have cut completion costs and improved production, especially in the case of horizontal wells. These new systems allow casings to run into the lateral zone with proper packer/frac port placement for optimal hydrocarbon recovery.
Production
The production stage is the most important stage of a well's life, when the oil and gas are produced. By this time, the oil rigs and workover rigs used to drill and complete the well have moved off the wellbore, and the top is usually outfitted with a collection of valves called a production tree. These valves regulate pressures, control flows, and allow access to the wellbore in case further completion work is needed. From the outlet valve of the production tree, the flow can be connected to a distribution network of pipelines and tanks to supply the product to refineries, natural gas compressor stations, or oil export terminals.
As long as the pressure in the reservoir remains high enough, the production tree is all that is required to produce the well. If the pressure depletes and it is considered economically viable, an artificial lift method mentioned in the completions section can be employed.
Workovers are often necessary in older wells, which may need smaller diameter tubing, scale or paraffin removal, acid matrix jobs, or completing new zones of interest in a shallower reservoir. Such remedial work can be performed using workover rigs also known as pulling units or completion rigs to pull and replace tubing, or by the use of well intervention techniques utilizing coiled tubing. Depending on the type of lift system and wellhead a rod rig or flushby can be used to change a pump without pulling the tubing.
Enhanced recovery methods such as water flooding, steam flooding, or CO2 flooding may be used to increase reservoir pressure and provide a "sweep" effect to push hydrocarbons out of the reservoir. Such methods require the use of injection wells (often chosen from old production wells in a carefully determined pattern), and are used when facing problems with reservoir pressure depletion, high oil viscosity, or can even be employed early in a field's life. In certain cases depending on the reservoir's geomechanics reservoir engineers may determine that ultimate recoverable oil may be increased by applying a waterflooding strategy early in the field's development rather than later. Such enhanced recovery techniques are often called "tertiary recovery".
Abandonment
When the well no longer produces or produces so poorly that it is a liability, it is abandoned. In this process, tubing is removed from the well and sections of well bore are filled with cement to isolate the flow path between gas and water zones from each other, as well as the surface. Completely filling the well bore with cement is costly and unnecessary. The surface around the wellhead is then excavated, and the wellhead and casing are cut off, a cap is welded in place and then buried.
The production from an oil well declines in production. The point at which the well no longer makes a profit and is plugged and abandoned is called the economic limit. The equation to determine the economic limit contains four factors, namely: (1) taxes, (2) operating cost, (3) oil price, and (4) royalty. When oil taxes are raised, the economic limit is raised. When oil price is increased, the economic limit is lowered.
When the economic limit is raised, the life of the well is decreased. Proven oil reserves are lost when the life of an oil well is decreased. Inversely, when the economic limit is lowered, the life of the well is increased. Proven oil reserves are increased when the life of the well is increased.
At the economic limit there often is still a significant amount of unrecoverable oil left in the reservoir. It might be tempting to defer physical abandonment for an extended period of time, hoping that the oil price will go up or that new supplemental recovery techniques will be perfected. However, lease provisions and governmental regulations usually require quick abandonment; liability and tax concerns also may favor abandonment.
In theory an abandoned well can be reentered and restored to production (or converted to injection service for supplemental recovery or for downhole hydrocarbons storage), but reentry often proves to be difficult mechanically and not cost effective.
Types of wells
Oil wells come in many varieties. By produced fluid, there can be wells that produce oil, wells that produce oil and natural gas, or wells that only produce natural gas. Natural gas is almost always a byproduct of producing oil, since the small, light gas carbon chains come out of solution as it undergoes pressure reduction from the reservoir to the surface, similar to uncapping a bottle of soda pop where the carbon dioxide effervesces. Unwanted natural gas can be a disposal problem at the well site. If there is not a market for natural gas near the wellhead it is virtually valueless since it must be piped to the end user. Until recently, such unwanted gas was burned off at the wellsite, but due to environmental concerns this practice is becoming less common. Often, unwanted (or 'stranded' gas without a market) gas is pumped back into the reservoir with an 'injection' well for disposal or repressurizing the producing formation. Another solution is to export the natural gas as a liquid. Gas-to-liquid, (GTL) is a developing technology that converts stranded natural gas into synthetic gasoline, diesel or jet fuel through the Fischer-Tropsch process developed in World War II Germany. Such fuels can be transported through conventional pipelines and tankers to users. Proponents claim GTL fuels burn cleaner than comparable petroleum fuels. Most major international oil companies are in advanced development stages of GTL production, with a world-scale (140,000 bbl/day) GTL plant in Qatar scheduled to come online before 2010. In locations such as the United States with a high natural gas demand, pipelines are constructed to take the gas from the wellsite to the end consumer.
Another obvious way to classify oil wells is by land or offshore wells. There is very little difference in the well itself. An offshore well targets a reservoir that happens to be underneath an ocean. Due to logistics, drilling an offshore well is far more costly than an onshore well. By far the most common type is the onshore well. These wells dot the Southern and Central Great Plains, Southwestern United States, and are the most common wells in the Middle East.
Another way to classify oil wells is by their purpose in contributing to the development of a resource. They can be characterized as:
- production wells are drilled primarily for producing oil or gas, once the producing structure and characteristics are determined
- appraisal wells are used to assess characteristics (such as flow rate) of a proven hydrocarbon accumulation
- exploration wells are drilled purely for exploratory (information gathering) purposes in a new area
- wildcat wells are drilled based on a large element of hope, in a frontier area where little is known about the subsurface. In the early days of oil exploration in Texas, wildcats were common as productive areas were not yet established. In modern times, oil exploration in many areas has reached a very mature phase and the chances of finding oil simply by drilling at random are very low, and much more effort is placed in exploration and appraisal wells.
At a producing well site, active wells may be further categorised as:
- oil producers producing predominantly liquid hydrocarbons, but mostly with some associated gas.
- gas producers producing almost entirely gaseous hydrocarbons.
- water injectors injecting water into the formation to maintain reservoir pressure or simply to dispose of water produced with the hydrocarbons because even after treatment, it would be too oily and too saline to be considered clean for dumping overboard, let alone into a fresh water source, in the case of onshore wells. Frequently water injection has an element of reservoir management and produced water disposal.
- aquifer producers intentionally producing reservoir water for re-injection to manage pressure. This is in effect moving reservoir water from where it is not as useful to where it is more useful. These wells will generally only be used if produced water from the oil or gas producers is insufficient for reservoir management purposes. Using aquifer produced water rather than sea water is due to the chemistry.
- gas injectors injecting gas into the reservoir often as a means of disposal or sequestering for later production, but also to maintain reservoir pressure.
Lahee classification
- New Field Wildcat (NFW) far from other producing fields and on a structure that has not previously produced.
- New Pool Wildcat (NPW) new pools on already producing structure.
- Deeper Pool Test (DPT) on already producing structure and pool, but on a deeper pay zone.
- Shallower Pool Test (SPT) on already producing structure and pool, but on a shallower pay zone.
- Outpost (OUT) usually two or more locations from nearest productive area.
- Development Well (DEV) can be on the extension of a pay zone, or between existing wells (Infill).
Cost
The following is a quick comparison of average well costs for the UK Continental Shelf (UKCS). These costs exclude testing (e.g., flow rate testing), and are based on values from March 1998. Prices have doubled since then :
Typical well costs for UKCS wells in 1998| Well location | Typical cost (in millions of £) | Northern North Sea | 8 – 12 | West of Shetland | 5 – 15 | Southern North Sea | 7 – 12 | Irish Sea | 2 – 3 |
The cost of an offshore well depends strongly on the remoteness of the location being drilled. Hence the Irish Sea (shallow water, close to the coast) is cheap in comparison to the West of Shetland (deep water, far from the coast and other facilities). The 2006 cost of a Central North Sea high pressure, high temperature well is about $35-50 million. Deep water wells in the Gulf of Mexico can cost over $100 million.
Onshore wells can be considerably cheaper, particularly if the field is at a shallow depth, where costs range from less than $1 million to $15 million for deep and difficult wells.
Reefs
Offshore platforms, the well's supporting structure, produce artificial reefs.
See also
External links
|
| |
|
|
