|
|
|
|
IBM 700/7000 series
|
| |
|
| |
The IBM 700/7000 series was a series of large scale (mainframe) computer systems made by IBM through the 1950s and early 1960s. The series included several different, incompatible processor architectures. The 700s used vacuum tube logic and were all made obsolete by the introduction of the transistorized 7000s.
Discussion
Ask a question about 'IBM 700/7000 series' Start a new discussion about 'IBM 700/7000 series' Answer questions from other users |
Encyclopedia
The IBM 700/7000 series was a series of large scale (mainframe) computer systems made by IBM through the 1950s and early 1960s. The series included several different, incompatible processor architectures. The 700s used vacuum tube logic and were all made obsolete by the introduction of the transistorized 7000s. The 7000s, in turn, were eventually replaced by System/360, which was announced in 1964. However the 360/65, the first 360 powerful enough to replace 7000s, did not become available until November 1965. Early problems with OS/360 and the high cost of converting software kept many 7000s in service for years afterwards.
Architectures
The IBM 700/7000 series had six completely different ways of storing data and instructions:
- First (36/18-bit words): 701 (Defense Calculator)
- Scientific (36-bit words): 704, 709, 7090, 7094, 7040, 7044
- Commercial (variable length character strings): 702, 705, 7080
- 1400 series (variable length character strings): 7010
- Decimal (10 digit words): 7070, 7072, 7074
- Supercomputer (64-bit words): 7030 "Stretch"
The 700 class used vacuum tubes, the 7000 class was transistorized. All machines (like most other computers of the time) used magnetic core memory; except for early 701 and 702 models, which used CRT memory. While the architectures differed, the machines in the same class shared electronics technologies and generally used the same peripherals including tape drives (IBM 727 and 729), card readers, card punches and printers. Early peripherals were based on IBM accounting machine technology and even used plug-boards. Later peripherals were adopted from the midline IBM 1400 series.
Early computers were sold without software. As operating systems began to emerge, having four different mainframe architectures plus the 1400 midline architectures became a major problem for IBM since it meant at least four different programming efforts were required.
The System/360 combined the best features of the 7000 and 1400 series architectures into a single design, however some 360 models had optional features that allowed them to emulate the 1400 and 7000 instruction sets in microcode. One of the selling points of the System/370 was improved 1400/7000 series emulation (it could be done under operating system control instead of shutting down and restarting in emulation mode as was done on the 360s).
First Architecture (701)
Known as the Defense Calculator while in development in the IBM Poughkeepsie Laboratory, this machine was formally unveiled April 7, 1953 as the IBM 701 Electronic Data Processing Machine.
Data formats
Numbers were either 36 bits or 18 bits long, only fixed point. (See: Why 36 bits?)
Instruction format
Instructions were 18 bits long, single address.
- Sign (1 bit) - Whole word (-) or Half word (+) operand address
- Opcode (5 bits) - 32 instructions
- Address (12 bits) - 4096 Half word addresses
To expand the memory from 2048 to 4096 words, a 33rd instruction was added that used the most significant bit of its address field to select the bank. (This instruction was probably created using the "No OP" instruction, which appears to have been the only instruction with unused bits, as it originally ignored its address field. However documentation on this new instruction is not currently available.)
Registers
Processor registers consisted of:
Memory
2,048 or 4,096 – 36-bit binary words with six-bit characters
Scientific Architecture (704/709/7090/7094)
Data formats
Numbers were 36 bits long, both fixed point and floating point. (See: Why 36 bits?)
- Fixed point numbers were stored in binary sign/magnitude format.
- Single precision floating point numbers had a magnitude sign, an 8-bit excess-128 exponent and a 29 bit magnitude
- Double precision floating point numbers, introduced on the 7094, had a magnitude sign, a 17-bit excess-65536 exponent, and a 54 bit magnitude
- Alphameric characters were 6-bit BCD, packed six to a word.
Instruction format
The basic instruction format was a 3-bit prefix, 15-bit decrement, 3-bit tag, and 15-bit address. The prefix field specified the class of instruction. The decrement field often contained an immediate operand to modify the results of the operation, or was used to further define the instruction type. The three bits of the tag specified three (seven in the 7094) index registers, the contents of which were subtracted from the address to produce an effective address. The address field either contained an address or an immediate operand.
Registers
Processor registers consisted of:
- AC - 38-bit Accumulator
- MQ - 36-bit Multiplier-Quotient
- XR - 15-bit Index Registers (three or seven)
- SI - 36-bit Sense Indicator
The Accumulator (and Multiplier-Quotient) registers operated in signed magnitude format.
The Index registers operated using two's complement format and when used to modify an instruction address were subtracted from the address in the instruction. On machines with three index registers, if the tag had 2 or 3 bits set (i.e. selected multiple registers) then their values were ORed together before being subtracted. The IBM 7094, with seven index registers had a "compatibility" mode to permit programs from earlier machines that used this trick to continue to be used.
The Sense Indicators permitted interaction with the operator via panel switches and lights.
Memory
- 704
- 4,096 or 8,192 or 32,768 – 36-bit binary words with six-bit characters
- 709, 7090, 7094, 7094 II
- 32,768 – 36-bit binary words with six-bit characters
Input/output
The 709/7090 series used Data Synchronizer Channels for high speed input/output, such as tape and disk. The DSCs executed their own simple programs from the computer memory that controlled the transfer of data between memory and the I/O devices. Punch card I/O and high speed printing were often performed by transferring magnetic tapes to an off-line IBM 1401. Later, the data channels were used to connect an 7094 and a 7044 to form the IBM 7094/7044 Direct Coupled System (DCS). In that configuration, the 7044 primarily handled I/O.
FORTRAN Assembly Program
The FORTRAN Assembly Program (FAP) was the default macro assembler for the 709, 7090, and 7094.
Its pseudo-operation BSS, used to reserve memory, is the origin of the common name of the "BSS section", still used in many assembly languages today for designating reserved memory address ranges of the type not having to be saved in the executable image.
Commercial architecture (702/705/7080)
The IBM 702 and IBM 705 were similar and the 705 could run many 702 programs without modification, but they were not completely compatible.
The IBM 7080 was a transistorized version of the 705, with various improvements. For backward compatibility it could be run in 705 I mode, 705 II mode, 705 III mode, or full 7080 mode.
Data format
Data was represented by a variable length string of characters terminated by a Record mark.
Instruction format
Five characters: one character opcode & 4 character address - OAAAA
Registers
- 702
- two Accumulators (A & B) - 512 characters
- 705
- one Accumulator - 256 characters
- 14 auxiliary storage units - 16 characters
- one auxiliary storage unit - 32 characters
- 7080
- one Accumulator - 256 characters
- 30 auxiliary storage units - 512 characters
- 32 communication storage units - 8 characters
Memory
- 702
- 2,000 to 10,000 characters in Williams tubes (in increments of 2,000 characters)
- Character cycle rate - 23 microseconds
- 705 (models I, II, or III)
- 20,000 or 40,000 or 80,000 characters of Core memory
- Character cycle rate - 17 microseconds or 9.8 microseconds
- 7080
- 80,000 or 160,000 characters of Core memory
- Character cycle rate - 2.18 microseconds
1400 series architecture (7010)
The 700/7000 commercial architecture inspired the very successful IBM 1400 series of mid-sized business computers. In turn, IBM later introduced a mainframe version of the IBM 1410 called the IBM 7010.
Data format
Data was represented by a variable length string of characters terminated by a Wordmark.
Instruction format
Variable length: 1, 2, 6, 7, 11, or 12 characters.
Registers
None, all instructions operated on memory.
Memory
100,000 characters.
Decimal architecture (7070/7072/7074)
The IBM 7070, IBM 7072, and IBM 7074 were decimal, fixed word length machines. They used a ten digit word like the smaller and older IBM 650, but were not instruction set compatible with the 650.
Data format
- Word length - 10 decimal digit plus sign
- Digit encoding - two-out-of-five code
- Floating point - optional. Two digit exponent.
- Three signs for each word - Plus, Minus and Alpha
- Plus and Minus indicated 10 digit numeric values.
- Alpha indicated 5 characters of text coded by pairs of digits. 61 = A, 91 = 1.
Instruction format
- All instructions one word
- 2 digit op code (including sign, Plus or Minus only)
- 2 digit index register
- 2 digit field control - allows selecting sets of digits, shifting left or right
- 4 digit address
Registers
- All registers one word, could also be addressed as memory
- Accumulators - 3 (addresses 9991, 9992, and 9993 - standard; 99991, 99992, and 99993 - extended 7074)
- Program register - 1 (address 9995 - standard; 99995 - extended 7074)
- Addressable from console only. Stores current instruction.
- Instruction counter - 1 (address 9999 - standard; 99999 - extended 7074)
- Addressable from console only.
- Index registers - 99 (addresses 0001-0099)
Memory
- 5000 to 9990 words (standard)
- 15000 to 30000 words (extended 7074)
- Access time - 6 microseconds (7070/7072), 4 microseconds (7074)
- Add time - 72 microseconds (7070), 12 microseconds (7072), 10 microseconds (7074)
IBM 700 series, vacuum tubes, 1950s
- IBM 701 - IBM's first electronic computer - introduced in 1952
- IBM 702 - commercial - introduced in 1953
- IBM 704 - scientific - introduced in 1954
- IBM 705 - commercial - introduced in 1954
- IBM 709 - scientific - introduced in 1958
IBM 7000 series, transistors, 1960s
- IBM 7010 - high end version of IBM 1410 - introduced in 1962
- IBM 7030 - Stretch supercomputer - introduced in 1961
- IBM 7040 - scientific - introduced in 1963
- IBM 7044 - scientific - introduced in 1963
- IBM 7070 - decimal - introduced in 1960
- IBM 7072 - decimal - introduced in 1962
- IBM 7074 - decimal - introduced in 1961; used by the U.S. Internal Revenue Service in 1962
- IBM 7080 - commercial - introduced in 1961
- IBM 7090 - scientific - introduced in 1959
- IBM 7094 - scientific - introduced in 1962
- IBM 7094 II - scientific - introduced in 1964
The IBM 7700 Data Acquisition System was not a member of the IBM 7000 series, despite its number and its announcement date of December 2, 1963.
External links
|
| |
|
|
