|
|
|
|
GM Y platform
|
| |
|
| |
The Y platform, or Y body, designation has been used twice by the General Motors Corporation to describe a series of vehicles all built on the same basic body and sharing many parts and characteristics. The first was for a group of entry-level compacts including the rear-engine Chevrolet Corvair from 1960 to 1964 and conventional front-engine compacts built by GM divisions Buick, Oldsmobile and Pontiac from 1961 to 1963.
Discussion
Ask a question about 'GM Y platform' Start a new discussion about 'GM Y platform' Answer questions from other users |
Encyclopedia
The Y platform, or Y body, designation has been used twice by the General Motors Corporation to describe a series of vehicles all built on the same basic body and sharing many parts and characteristics. The first was for a group of entry-level compacts including the rear-engine Chevrolet Corvair from 1960 to 1964 and conventional front-engine compacts built by GM divisions Buick, Oldsmobile and Pontiac from 1961 to 1963. The second, and current, incarnation is used for a high-end rear-wheel drive automobile platform from the 1980s through the 2000s.
First Y platform (1960-1964)
The original Y bodies were:
Initially, each of the Y-body compacts from Buick, Olds and Pontiac were only offered as four-door sedans and station wagons when introduced in the fall of 1960 as 1961 models. In mid-1961, each of three divisions introduced two-door pillared coupes to the line with sportier versions of the Buick and Olds models added including the Special Skylark and F-85 Cutlass, both of which featured bucket seats, custom interior and exterior trim, and more powerful engines. For 1962, convertibles were added to the lineup by each of the divisions, with Pontiac also adding the sportier Tempest LeMans coupe and convertible to its compact lineup.
Also, the rear-engined 1960-69 Chevrolet Corvair used a variation of the Y-body through the 1964 model year with a rear swing-axle suspension and a transaxle similar to that found on the 1961-63 Pontiac Tempest. The 1961-62 Corvair station wagons even shared the same roofline as the 1961-63 Y-body wagons. The Corvair would undergo major styling and engineering changes for 1965, when it switched to a new Z-body. Chevrolet's front-engine compact, introduced as the Chevy II for 1962 had some dimensions similar to the Y-body cars, but had a two-inch shorter wheelbase and was also shorter in length and width, its its own X-body platform which featured unit-body construction, single-leaf rear suspension and conventional in-line four- and six-cylinder engines.
First Y platform innovations
The Y-body family of cars contained more innovative features than all other American products of that decade. Each model contained at least one notable advance:
- Chevrolet Corvair featured a rear-mounted six-cylinder engine that included many aluminum components and an aluminum block, along with a rear swing-axle suspension and rear transaxle. The 1960 model Corvair also offered a gasoline-powered heater as an option.
- Buick Special and Oldsmobile F-85 for all three years shared an aluminum block 215 cubic-inch V8 engine featuring cast-iron liners to prevent overheating and block warpage problems common with aluminum block engines. Although Buick and Olds shared the same basic engine design, both divisions used different camshafts, carburetors and compression ratios. The 215 V8 was also available on the Pontiac Tempest for 1961 and 1962, but very few Tempests were so-equipped.
- For 1962, Buick introduced a new 198 cubic-inch V6 engine for the lower-line Special models in order to allow for a lower base price. That V6 shared many parts and dimensions with the aluminum V8 engine but featured a cast iron block. This was the first production V6 engine to be offered in a passenger car.
- Oldsmobile introduced a turbocharged version of the 215 V8 in mid-1962 for a special performance version of the F-85/Cutlass called the Jetfire. This engine was among the first production turbocharged engines ever offered in a passenger car, the other being the Chevrolet Corvair's 164 cubic-inch six-cylinder introduced simultaneously for the Monza Spyder. The Olds Jetfire turbocharged V8 featured a four-barrel, 10.25 to 1 compression and was rated at 215 horsepower - one horsepower per cubic inch.
- The Pontiac Tempest came standard with a 195 cubic-inch slant four-cylinder engine - then the only U.S.-built passenger car with such an engine. The Tempest four was really create from half a 389 cubic inch V8 block used in the standard Pontiacs. This engine, available with one- and four-barrel carburetion offered horsepower ratings ranging from 110 to 166.
- The Tempest also used a rear transmission, or transaxle to permit a flat floor, eliminating the driveshaft hump, for improved interior space, while the Buick Special and Olds F-85 used a conventional front engine/front transmission drivetrain. * The Tempest also used an independent rear swing axle suspension similar to the rear-engine Chevy Corvair while the Buick and Olds compacts featured a conventional rear coil spring suspension.
- For 1963, Pontiac replaced the Buick-sourced 215 aluminum V8 with a Pontiac built 326 cubic-inch V8 as the top power option for the Tempest. This 326 was based on the big Pontiac's 389 V8 and shared many of the larger engine's dimensions and components with horsepower ratings of 264 and 280. The '63 326 Tempest/LeMans served as a testbed for the 389-powered 1964 GTO that would be based on a larger and more conventionally engineered Tempest introduced the following year.
Motor Trend magazine named the Corvair as its 1960 Car of the Year, Tempest as 1961's Car of the Year, and the V6 Special received the award in 1962.
End of the first Y platform
Each of the Buick, Olds and Pontiac Y-body senior compacts were replaced a larger intermediate-sized platform called the A-Body for the 1964 model year, which was shared with the Chevrolet Chevelle. With the switch from a senior compact to an intermediate-sized platform, most of these "innovative" features were discontinued such as the Tempest's four-cylinder engine and transaxle, the aluminum block V8 (whose tooling was sold to Rover of England) and the Olds Jetfire's turbocharged version of that V8. Also, the unit-body construction used in the Y-body cars was replaced by conventional body-on-frame construction for the A-body. The Buick V6 was continued and enlarged to 225 cubic inches with the basic engine remaining in production for many years, still in production today with a 3.8-liter or 231 cubic-inch displacement. The aluminum V8 was replaced by conventional cast-iron block V8s of 300 cubic inches for the Buick Special/Skylark and 330 inches for the Oldsmobile F-85/Cutlass, while Pontiac carried over its 326 cubic-inch V8 to the '64 Tempest/LeMans line while switching the base engine from the four-cylinder to a 215 cubic-inch inline six-cylinder.
Second Y platform
Y bodies built after 1964 can be identified by the inclusion of the Y as the fourth character in the Vehicle Identification Number, or VIN. Only two Y-body cars have been produced in this second group:
GM's Kappa platform was based on the Y-body. The distinctive feature of both platforms is the backbone central-tunnel design.
External links
|
| |
|
|
