Cassette (bicycle part)
Encyclopedia
On a bicycle
Bicycle
A bicycle, also known as a bike, pushbike or cycle, is a human-powered, pedal-driven, single-track vehicle, having two wheels attached to a frame, one behind the other. A person who rides a bicycle is called a cyclist, or bicyclist....

, the cogset or cluster is the set of multiple rear sprocket
Sprocket
A sprocket or sprocket-wheel is a profiled wheel with teeth, cogs, or even sprockets that mesh with a chain, track or other perforated or indented material. The name 'sprocket' applies generally to any wheel upon which are radial projections that engage a chain passing over it...

s that attaches to the hub on the rear wheel
Bicycle wheel
A bicycle wheel is a wheel, most commonly a wire wheel, designed for bicycle. A pair is often called a wheelset, especially in the context of ready built "off the shelf" performance-oriented wheels....

. A cogset works with a rear derailleur as part of the drivetrain
Bicycle drivetrain systems
Bicycle drivetrain systems are used to transmit power on bicycles, tricycles, quadracycles, unicycles, or other human-powered vehicles from the riders to the drive wheels. Most also include some type of a mechanism to convert speed and torque via gear ratios....

 to provide multiple gear ratio
Gear ratio
The gear ratio of a gear train is the ratio of the angular velocity of the input gear to the angular velocity of the output gear, also known as the speed ratio of the gear train. The gear ratio can be computed directly from the numbers of teeth of the various gears that engage to form the gear...

s to the rider. Cogsets come in two varieties, cassettes or freewheels, of which cassettes are a newer development. Although cassettes and freewheels perform the same function and look almost the same when installed, they have important mechanical differences and are not interchangeable. The terms are sometimes incorrectly used interchangeably.

Freewheels

A freewheel
Freewheel
thumb|Freewheel mechanismIn mechanical or automotive engineering, a freewheel or overrunning clutch is a device in a transmission that disengages the driveshaft from the driven shaft when the driven shaft rotates faster than the driveshaft...

 (also known as a block) consists of either a single sprocket or a set of sprockets mounted on a body which contains an internal ratcheting
Ratchet (device)
A ratchet is a device that allows continuous linear or rotary motion in only one direction while preventing motion in the opposite direction. Because most socket wrenches today use ratcheting handles, the term "ratchet" alone is often used to refer to a ratcheting wrench, and the terms "ratchet"...

 mechanism and mounts on a threaded hub. Threaded rear hubs were available in different thread patterns depending on the country of manufacture, French and British threads being the most common. British CEI (Cycle Engineers Institute) thread was adopted as the international standard and is now known as B.S.C. - British Standard Cycle and is a standardized right-hand thread (1.375 x 24 TPI) onto which a standard freewheel is screwed. This allows different brands of freewheels to be mounted on different brands of hubs.

The major disadvantage of the multiple sprocket freewheel design is that the drive-side bearing is located inboard of the freewheel, and as sprockets were added over time in the quest for multiple derailleur gearing, moved the bearing potentially far from the drive-side axle support. The farther from the support, the more flexing stress is placed on the axle which can bend or even break. Multiple freewheels were common on quality high end bikes until the late 1980s. Suntour - Maeda Industries (Japan) introduced a compact 6 speed block which reduced the spacing between the sprockets and was the same width as a standard 5 speed block but required a narrower chain than the standard 1/2 x 3/32 chain. The concept was copied by European freewheel manufacturers Regina (Italy) and Maillard (France). As the number of sprockets on a multiple freewheel increased beyond five during the 1970s and clusters became physically wider, the freehub design overcame the axle/bearing problem with threaded hubs and began to supersede the freewheel design. Today it is rare to find a freewheel on a new bicycle with more than seven speeds. Some new single-speed
Single-speed bicycle
A single-speed bicycle is a type of bicycle with a single gear ratio. These bicycles are without derailleur gears, hub gearing or other methods for varying the gear ratio of the bicycle....

 — especially BMX
BMX
Bicycle motocross or BMX refers to the sport in which the main goal is extreme racing on bicycles in motocross style on tracks with inline start and expressive obstacles, and it is also the term that refers to the bicycle itself that is designed for dirt and motocross cycling.- History :BMX started...

 and utility bikes
Utility bicycle
A utility bicycle is a bicycle designed for practical transportation, as opposed to bicycles which are primarily designed for recreation and competition, such as touring bicycles, racing bicycles, sport/training bicycles, and mountain bicycles. The vast majority of bicycles can be found in the...

 — and lower-end multi-geared bicycles continue to be manufactured and sold with freewheels.

Pedaling forces tighten a freewheel onto the hub, so no tool is required to install one. However, the ratcheting mechanism prevents loosening a freewheel simply by turning the sprockets counter-clockwise. Instead, a freewheel can be removed from the hub with one of the many specific freewheel removal tools that engages a spline or set of notches on the outboard end of the freewheel. Removal often requires considerable effort due to the large torque that tightens the freewheel during pedaling, and some freewheels cannot be removed intact. Future removal of a freewheel is facilitated by grease on the freewheel threads before installation.

Cassettes

Cassettes are distinguished from freewheels in that a cassette has a series of straight splines
Rotating spline
Splines are ridges or teethon a drive shaft that mesh with grooves in a mating piece and transfer torque to it, maintaining the angular correspondence between them....

 that form the mechanical connection between the sprockets and the cassette compatible hub, called a freehub
Freehub
A freehub is a type of bicycle hub that incorporates a ratcheting mechanism, and the name freehub is a registered trademark of Shimano. A set of sprockets are mounted onto a splined shaft of the freehub to engage the chain...

, which contains the ratcheting mechanism. The entire cassette is held on the hub by means of a threaded lockring
Lockring
A lock ring is a threaded washer used to prevent components from becoming loose during rotation. They are found on an adjustable bottom bracket and a track hub of a bicycle. Lokring is another form of fastener used in the automotive and air condition industries. These fittings are often confused...

. Some cassette systems from the late 1980s and early 1990s use a threaded small sprocket to hold on the larger splined sprockets, the entire set referred to as a cluster. Cassettes resemble freewheels when installed, but are clearly different off the wheel due to the lack of a contained freewheel mechanism.

The sprockets in a cassette are usually held together by three small bolts or rivets for ease of installation. These bolts or rivets are by no means necessary, they just keep the sprockets and spacers in the correct order and position when they are removed from the freehub body. When the sprockets need to be replaced due to wear or the user wishes to change gear ratio
Gear ratio
The gear ratio of a gear train is the ratio of the angular velocity of the input gear to the angular velocity of the output gear, also known as the speed ratio of the gear train. The gear ratio can be computed directly from the numbers of teeth of the various gears that engage to form the gear...

s available, only the sprockets are replaced, not the ratchet mechanism. Cassettes also allow the use of sprockets with fewer teeth, as in micro drive
Micro drive
Micro drive is a term used to describe the drivetrain, mostly BMX and MTB, that use smaller than standard sized cogs. The smallest rear sprocket that fits on a freehub body is an 11-tooth, but with the use of a cassette hub, sometimes called a micro drive rear hub, sprockets as small as 8 teeth may...

 systems.

The ratchet mechanism, known as the freehub body, is still replaceable on most hubs, but forms a structural part of the hub. Cassette systems have a major advantage in that the drive-side axle bearing can be out near the frame, rather than being back towards the centre of the axle behind the freewheel. This greatly reduces the stress on the rear axle, making bent or broken axles extremely rare.

Since their introduction in the late 1970s cassettes have been used on increasing numbers of bicycles, starting at the high-end and over time becoming available on less expensive bikes. Today all higher quality derailleured
Derailleur gears
Derailleur gears are a variable-ratio transmission system commonly used on bicycles, consisting of a chain, multiple sprockets of different sizes, and a mechanism to move the chain from one sprocket to another...

 bicycles use this newer design.

Number and width of sprockets

Over time, the number of sprockets in a cogset has increased, from three or four before World War II
World War II
World War II, or the Second World War , was a global conflict lasting from 1939 to 1945, involving most of the world's nations—including all of the great powers—eventually forming two opposing military alliances: the Allies and the Axis...

, to five used from the 1950s to the 1970s, then six or seven through to the eight, nine, ten or even eleven now found on modern bikes. As more rear sprockets were added, the combination became wider, and the sprocket spacing narrower. To accommodate the increased number of sprockets, the axle (measured as the Over Locknut Distance - O.L.D.) was lengthened, necessitating more dish on the rear wheel drive side with a threaded hub to centre the wheel in the frame. The hub flange
Flange
A flange is an external or internal ridge, or rim , for strength, as the flange of an iron beam such as an I-beam or a T-beam; or for attachment to another object, as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera; or for a flange of a rail car or tram wheel...

s spacing was not shortened on threaded hubs, rather the axle length increased from 120 mm O.L.D. (five-speed/compact six) to 126 mm O.L.D. (six-speed/compact seven) through to 130 mm O.L.D. (threaded seven-speed) for a road bike. MTB rear spacing is normally 135 mm O.L.D. Another advantage of the Shimano cassette hubs introduced from 1978 was that the rear hub flanges were wider apart than those of a threaded hub, so built a stronger wheel with less dish and without the problem of increased bearing stress or axle failure. Shimano also changed the shape of the teeth on their sprockets, making some shorter, machining ramps and turning the sprocket teeth to facilitate easier gear changing for their index system. Shimano chains were also designed to be more flexible than the older pattern Renold/Coventry 1/2 x 3/32 five-speed chains.

Before the introduction of indexed shifting, the standard width of a five-speed or compact six block was 32 mm, but the introduction of indexed shifting supposedly made standardized sprocket spacing necessary. Shimano and Campagnolo
Campagnolo
Campagnolo is an Italian manufacturer of high-end bicycle components with headquarters in Vicenza, Italy. The components are organised as groupsets and are a near-complete collection of a bicycle's mechanical parts. Campagnolo's flagship components are the Super Record, Record, and Chorus...

 both came up with independent standards, and SRAM later followed Shimano's lead in respect to sprocket spacing and cassette width. The width of early Shimano six- and seven-speed cassettes was 36 mm, and early eight-speed 40 mm wide. Shimano then changed again and standardised eight-11 speed cassettes on 41.5 mm and second generation seven-speed to 38 mm. The widening of the sprocket carrier on the cassette hubs to 41.5 mm resulted in a decrease in the distance between the hub flanges.

For Shimano and SRAM the cassette spacing developed as follows. Early Shimano seven-speed cassettes are 36 mm wide, with sprocket spacing of 3.65 mm, but levers and rear dearilleurs are not compatible with later Shimano seven-speed cassettes, which are 38 mm wide and have 3.2 mm sprocket spacing. An eight-speed cassette is wider at 41.5 mm than a second generation Shimano seven. This results in functionally compatible shifters, but specific freehub bodies, or necessitating the use of a spacer with a seven-speed cassette on an eight-speed hub. Eight- and nine-speed cassettes and freehub bodies have the same width (41.5 mm), but with the sprockets closer together; as a result the shifters are not compatible, but they use the same freehub bodies. Ten-speed cassettes are slightly more narrow than eight/nine so they fit on those freehubs but need a spacer, conversely eight/nine-speed cassettes do not fit on ten-speed freehubs.

This progression has provided more fine adjustment of gear ratio, however the use of thinner metal parts has had the effect of shortening the life-span of the chain and sprockets due to so called "stretching" of the chain. This is caused by frictional abrasion of the load-bearing surfaces of the chain causing elongation. As such, the chain and sprockets of a nine-speed system require more frequent replacement than an eight. The narrowing of the hub flanges has created more dish in the wheel, which weakens the wheel if all other factors are the same, but improvements in the strength and reliability of spokes and rims has more than balanced this out, and wheel strength is generally higher despite the increased dish.

Improvements in shifting

Shift ramps are complex tooth profiles, in the rear sprockets and front chainrings, designed to pick up and drop the chain
Bicycle chain
A bicycle chain is a roller chain that transfers power from the pedals to the drive-wheel of a bicycle, thus propelling it. Most bicycle chains are made from plain carbon or alloy steel, but some are nickel-plated to prevent rust, or simply for aesthetics. Nickel also confers a measure of...

 during shifting. They allow for shifting under greater load than was previously possible, and for smoother and cleaner shifting. The different systems are branded Hyperglide by Shimano
Shimano
Shimano, Inc. is a Japanese multinational manufacturer of cycling components, fishing tackle, and rowing equipment.In 2005, the company had net sales of US $1.4 billion. Bicycle components provided 75% of its sales income...

, UltraDrive by Campagnolo
Campagnolo
Campagnolo is an Italian manufacturer of high-end bicycle components with headquarters in Vicenza, Italy. The components are organised as groupsets and are a near-complete collection of a bicycle's mechanical parts. Campagnolo's flagship components are the Super Record, Record, and Chorus...

, and OpenGlide by SRAM
SRAM (bicycles)
SRAM Corporation is a privately held bicycle component manufacturer based in Chicago, Illinois, founded in 1987. SRAM is an acronym comprising the names of its founders, Scott, Ray, and Sam, .In 2008, the company received a strategic investment from Trilantic Capital Partners, formerly known as...

. The chain itself is specifically manufactured for ease of shifting, and to interface with a particular manufacturer's shift ramps; using a different type of chain may result in sub-optimal shifting.

External links

The source of this article is wikipedia, the free encyclopedia.  The text of this article is licensed under the GFDL.
 
x
OK