Balanced audio
Encyclopedia
Balanced audio is a method of interconnecting audio equipment using impedance-balanced lines
Balanced line
In telecommunications and professional audio, a balanced line or balanced signal pair is a transmission line consisting of two conductors of the same type, each of which have equal impedances along their lengths and equal impedances to ground and to other circuits. The chief advantage of the...

. This type of connection is very important in sound recording and production because it allows for the use of long cables while reducing susceptibility to external noise.

Balanced connections use three-conductor connectors, usually the XLR
XLR connector
The XLR connector is a style of electrical connector, primarily found on professional audio, video, and stage lighting equipment. The connectors are circular in design and have between 3 and 7 pins...

 or TRS connector
TRS connector
A TRS connector is a common family of connector typically used for analog signals including audio. It is cylindrical in shape, typically with three contacts, although sometimes with two or four . It is also called an audio jack, phone jack, phone plug, and jack plug...

. XLR connectors, for instance, are usually used with microphone
Microphone
A microphone is an acoustic-to-electric transducer or sensor that converts sound into an electrical signal. In 1877, Emile Berliner invented the first microphone used as a telephone voice transmitter...

s because of their durable construction, while TRS jack plugs are usually used for mixer
Mixing console
In professional audio, a mixing console, or audio mixer, also called a sound board, mixing desk, or mixer is an electronic device for combining , routing, and changing the level, timbre and/or dynamics of audio signals. A mixer can mix analog or digital signals, depending on the type of mixer...

 inputs and outputs because of their smaller profile.

Applications

Many microphones operate at low voltage levels and some with high output impedance
Output impedance
The output impedance, source impedance, or internal impedance of an electronic device is the opposition exhibited by its output terminals to an alternating current of a particular frequency as a result of resistance, inductance and capacitance...

 (hi-Z), which makes long microphone cables especially susceptible to electromagnetic interference
Electromagnetic interference
Electromagnetic interference is disturbance that affects an electrical circuit due to either electromagnetic induction or electromagnetic radiation emitted from an external source. The disturbance may interrupt, obstruct, or otherwise degrade or limit the effective performance of the circuit...

. Microphone interconnections are therefore a perfect application for a balanced interconnection, which cancels out most of this induced outside noise.

If the power amplifiers of a public address system are located at any distance from the mixing console
Mixing console
In professional audio, a mixing console, or audio mixer, also called a sound board, mixing desk, or mixer is an electronic device for combining , routing, and changing the level, timbre and/or dynamics of audio signals. A mixer can mix analog or digital signals, depending on the type of mixer...

, it is also normal to use balanced lines for the signal paths from the mixer to these amplifiers. Many other components, such as graphic equalizers and effects units, have balanced inputs and outputs to allow this. In recording and for short cable runs in general, a compromise is necessary between the noise reduction given by balanced lines and the cost introduced by the extra circuitry
Electronic circuit
An electronic circuit is composed of individual electronic components, such as resistors, transistors, capacitors, inductors and diodes, connected by conductive wires or traces through which electric current can flow...

 they require.

Interference reduction

Balanced audio connections use a number of techniques to reduce noise.

A typical balanced cable contains two identical wires, which are twisted together and then wrapped with a third conductor (foil or braid) that acts as a shield
Shielded cable
A shielded or screened cable is an electrical cable of one or more insulated conductors enclosed by a common conductive layer. The shield may be composed of braided strands of copper , a non-braided spiral winding of copper tape, or a layer of conducting polymer. Usually, this shield is covered...

.
The term "balanced" comes from the method of connecting each wire to identical impedances
Electrical impedance
Electrical impedance, or simply impedance, is the measure of the opposition that an electrical circuit presents to the passage of a current when a voltage is applied. In quantitative terms, it is the complex ratio of the voltage to the current in an alternating current circuit...

 at source and load. This means that much of the electromagnetic interference will induce an equal noise voltage in each wire. Since the amplifier at the far end measures the difference
Subtraction
In arithmetic, subtraction is one of the four basic binary operations; it is the inverse of addition, meaning that if we start with any number and add any number and then subtract the same number we added, we return to the number we started with...

 in voltage between the two signal lines, noise that is identical on both wires is rejected. The noise received in the second, inverted line is applied against the first, upright signal, and cancels it out when the two signals are subtracted.

This differential signal recombination can be implemented with a differential amplifier
Differential amplifier
A differential amplifier is a type of electronic amplifier that amplifies the difference between two voltages but does not amplify the particular voltages.- Theory :Many electronic devices use differential amplifiers internally....

. A balun
Balun
A balun is a type of electrical transformer that can convert electrical signals that are balanced about ground to signals that are unbalanced , and the reverse. They are also often used to connect lines of differing impedance...

 may also be used instead of an active differential amplifier device.

The wires are also twisted together, to reduce interference from electromagnetic induction
Electromagnetic induction
Electromagnetic induction is the production of an electric current across a conductor moving through a magnetic field. It underlies the operation of generators, transformers, induction motors, electric motors, synchronous motors, and solenoids....

. A twisted pair
Twisted pair
Twisted pair cabling is a type of wiring in which two conductors are twisted together for the purposes of canceling out electromagnetic interference from external sources; for instance, electromagnetic radiation from unshielded twisted pair cables, and crosstalk between neighboring pairs...

 makes the loop area between the conductors as small as possible, and ensures that a magnetic field that passes equally through adjacent loops will induce equal levels of noise on both lines, which is canceled out by the differential amplifier. If the noise source is extremely close to the cable, then it is possible it will be induced on one of the lines more than the other, and it won't be canceled as well, but canceling will still occur to the extent of the amount of noise that is equal on both lines.

The separate shield of a balanced audio connection also yields a noise rejection advantage over an unbalanced two-conductor arrangement (such as used in typical home stereos) where the shield must also act as the signal return wire. Any noise currents induced into a balanced audio shield will not therefore be directly modulated onto the signal, whereas in a two-conductor system they will be. This also prevents ground loop
Ground loop (electricity)
In an electrical system, a ground loop usually refers to a current, almost always unwanted, in a conductor connecting two points that are supposed to be at the same potential, often ground, but are actually at different potentials. Ground loops created by improperly designed or improperly installed...

 problems, by separating the shield/chassis from signal ground.

Differential signalling

Signals are often transmitted over balanced connections using the differential mode, meaning the wires carry signals of opposite polarity
Electrical polarity
Electrical polarity is present in every electrical circuit. Electrons flow from the negative pole to the positive pole. In a direct current circuit, one pole is always negative, the other pole is always positive and the electrons flow in one direction only...

 to each other (for instance, in an XLR connector
XLR connector
The XLR connector is a style of electrical connector, primarily found on professional audio, video, and stage lighting equipment. The connectors are circular in design and have between 3 and 7 pins...

, pin 2 carries the signal with normal polarity, and pin 3 carries an inverted version of the same signal).

Despite popular belief, this is not necessary for noise rejection. As long as the impedances are balanced, noise will couple equally into the two wires (and be rejected by a differential amplifier), regardless of the signal that is present on them. A simple method of driving a balanced line is to inject the signal into the "hot" wire through a known source impedance, and connect the "cold" wire to ground through an identical impedance. Due to common misconceptions about differential signalling, this is often referred to as a quasi-balanced or impedance-balanced output, though it is, in fact, fully balanced and will reject common-mode interference.

However, there are some minor benefits to driving the line with a fully differential output:
  • The electromagnetic field around a differential line is ideally zero, which reduces crosstalk into adjacent cables, useful for telephone pairs.
  • Though the signal level would not be changed due to nominal level
    Nominal level
    Nominal level is the operating level at which an electronic signal processing device is designed to operate. The electronic circuits that make up such equipment are limited in the maximum signal they can output and the low-level internally-generated electronic noise they add to the signal...

     standardization, the maximum output from the differential drivers is twice as much, giving 6 dB extra headroom. (If the amplifiers are identical, though, their output noise sums to 3 dB more than a single amplifier, decreasing dynamic range).
  • Increasing cable capacitance over long cable runs decreases the signal level at which high frequencies are attenuated. If each wire carries half the signal voltage swing as in fully differential outputs then longer cable runs can be used without the loss of high frequencies.
  • Noise that is correlated between the two amps (from imperfect power supply rejection, for instance), would be cancelled out.
  • At higher frequencies, the output impedance of the output amplifier can change, resulting in a small imbalance. When driven in differential mode by two identical amplifiers, this impedance change will be the same for both lines, and thus cancelled out.
  • Differential drivers are also more forgiving of incorrectly wired adapters or equipment that unbalances the signal by shorting pin 2.

Internally balanced audio design

Most professional audio products (recording, public address, etc.) provide differential balanced inputs and outputs, typically via XLR or TRS connector
TRS connector
A TRS connector is a common family of connector typically used for analog signals including audio. It is cylindrical in shape, typically with three contacts, although sometimes with two or four . It is also called an audio jack, phone jack, phone plug, and jack plug...

s. However, in most cases, a differential balanced input signal is internally converted to a single-ended signal via transformer
Transformer
A transformer is a device that transfers electrical energy from one circuit to another through inductively coupled conductors—the transformer's coils. A varying current in the first or primary winding creates a varying magnetic flux in the transformer's core and thus a varying magnetic field...

 or electronic amplifier
Amplifier
Generally, an amplifier or simply amp, is a device for increasing the power of a signal.In popular use, the term usually describes an electronic amplifier, in which the input "signal" is usually a voltage or a current. In audio applications, amplifiers drive the loudspeakers used in PA systems to...

. After internal processing, the single-ended signal is converted back to a differential balanced signal and fed to an output. A small number of professional audio products have been designed as an entirely differential balanced signal path from input to output; the audio signal never unbalances. This design is achieved by providing identical (mirrored) internal signal paths for both pin 2 and pin 3 signals (AKA "hot" and "cold" audio signals). In critical applications, a 100% differential balanced circuit
Balanced circuit
A balanced circuit is circuitry for use with a balanced line or the balanced line itself. Balanced lines are a common method of transmitting many types of electrical communication signals between two points on two wires...

 design can offer better signal integrity
Signal integrity
Signal integrity or SI is a set of measures of the quality of an electrical signal. In digital electronics, a stream of binary values is represented by a voltage waveform. However, digital signals are fundamentally analog in nature, and all signals are subject to effects such as noise,...

 by avoiding the extra amplifier stages or transformer
Transformer
A transformer is a device that transfers electrical energy from one circuit to another through inductively coupled conductors—the transformer's coils. A varying current in the first or primary winding creates a varying magnetic flux in the transformer's core and thus a varying magnetic field...

s required for front-end unbalancing and back-end rebalancing. Fully balanced internal circuitry has been promoted as yielding 3dB better dynamic range.

Connectors

While 3-pin XLR connectors are the most common balanced connector, quarter-inch (¼" or 6.35 mm) TRS connectors (tip-ring-sleeve) are also commonly used. Many hybrid jacks are now designed to take either XLR or TRS.
On TRS plugs, the tip is "hot" (positive), the ring is "cold" (negative), and the sleeve is ground (earthed
Ground (electricity)
In electrical engineering, ground or earth may be the reference point in an electrical circuit from which other voltages are measured, or a common return path for electric current, or a direct physical connection to the Earth....

 or chassis
Chassis
A chassis consists of an internal framework that supports a man-made object. It is analogous to an animal's skeleton. An example of a chassis is the underpart of a motor vehicle, consisting of the frame with the wheels and machinery.- Vehicles :In the case of vehicles, the term chassis means the...

). If a stereophonic or other binaural
Binaural
Binaural literally means "having or relating to two ears." Binaural hearing, along with frequency cues, lets humans and other animals determine direction of origin of sounds...

 signal is plugged into such a jack, one channel (usually the right) will be subtracted from the other (usually the left), leaving an unlistenable L − R (left minus right) signal instead of normal monophonic
Monaural
Monaural or monophonic sound reproduction is single-channel. Typically there is only one microphone, one loudspeaker, or channels are fed from a common signal path...

 L + R. Reversing the polarity
Electrical polarity
Electrical polarity is present in every electrical circuit. Electrons flow from the negative pole to the positive pole. In a direct current circuit, one pole is always negative, the other pole is always positive and the electrons flow in one direction only...

 at any other point in a balanced audio system will also result in this effect at some point when it is later mixed-down with its other channel.

Telephone line
Telephone line
A telephone line or telephone circuit is a single-user circuit on a telephone communication system...

s also carry balanced audio, though this is generally now limited to the local loop
Local loop
In telephony, the local loop is the physical link or circuit that connects from the demarcation point of the customer premises to the edge of the carrier or telecommunications service provider's network...

. It is called this because the two wires form a balanced loop through which both sides of the telephone call
Telephone call
A telephone call is a connection over a telephone network between the calling party and the called party.-Information transmission:A telephone call may carry ordinary voice transmission using a telephone, data transmission when the calling party and called party are using modems, or facsimile...

 travel.

Data lines, including digital audio
Digital audio
Digital audio is sound reproduction using pulse-code modulation and digital signals. Digital audio systems include analog-to-digital conversion , digital-to-analog conversion , digital storage, processing and transmission components...

, are also frequently balanced, normally using AES3 (AES/EBU) with XLR connectors for pro audio. Eight-channel analog balanced audio connectors like ADAT
ADAT
Alesis Digital Audio Tape or ADAT is a magnetic tape format used for the simultaneous digital recording of eight analog audio or digital audio tracks at once, onto a Super VHS tape that is used by consumer VCRs.- History :...

 use DB25 connectors, which can also carry up to 16 digital channels.

Converters

Unbalanced signals can be converted to balanced signals by the use of a balun
Balun
A balun is a type of electrical transformer that can convert electrical signals that are balanced about ground to signals that are unbalanced , and the reverse. They are also often used to connect lines of differing impedance...

, often through a DI unit
DI unit
A DI unit, DI box, Direct Box, or simply DI , is a device typically used in recording studios to connect a high-impedance, line level, unbalanced output signal to a low-impedance microphone level balanced input, usually via XLR connector...

.

If balanced audio must be fed into an unbalanced connection the electronic design used for the balanced output stage must be known. In most cases the negative output can be tied to ground but in certain cases the negative output should be left disconnected.

External links

The source of this article is wikipedia, the free encyclopedia.  The text of this article is licensed under the GFDL.
 
x
OK